Plates: I made plates from a suggestion that I got right here off the digest! Forgive me for not remembering the name of the person, but she said that the little rings from the orange juice containers looked liked they could be made into plates, and she was absolutely right. I carefully removed the "plate" from the pulley thingie with a razor. I placed a small butterfly nail decal in the center of each and painted the edges in metallic gold powder mixed with gloss. I then applied the gloss over the entire plate, and voila! I had four very pretty plates.

Tonya


Hinges on Wicker: I made a wicker picnic basket that turned out really cute. The inside is lined with red & white gingham material. The "hinge" is made of the same fabric and glued underneath the lining of the basket as well as the lid.

Anita Myers


Wicker basket hinges: Quite a few furniture kits are too small for hinges, so they use ribbon (I think 1/4") for the hinges. Fernwood kits have you cut a little out of both the frame and door to the depth of the ribbon, so not much, then glue the ribbon inside for hinges. You'd need two tiny pieces, but it's not difficult.

Patricia LeBeau


Sewing Basket: The cloth hinge sounds like the best one, but you could also use a needle with the waxed linen and run through the lid and basket about 3 times for each hinge.

MaryLou in Middleburg Hts., OH


Straw Hat Instructions: The straw is woven with cotton threads on either side...Pick one thread out and pull, this will curve into a circle. this starts the process.. You will need a small round object to work the hat on, a wine cork is perfect :) , or the top off a glue stick. You can either glue...or..sew..the choice is yours. Gluing, overlap slightly and iron when finished.

Instructions for sewing - Butt up the edges and sew with a tiny overstitch. Sew the top of the crown section to form a small flat circle just big enough to cover the cork. Hold the cork in your left hand.. hold the circle of straw ..and continue to sew down and around the sides of the cork for about two widths of the straw. Overlap the straw to make a straight edge...secure and cut off If making a 'picture hat' you now need to make a flat brim. Draw a circle on card, place the cork in the centre and draw around. This gives you the area to work. Gently pull the straw to form the circle....join the edges by overlapping and sew in place and continue to sew edge to edge until it measures your brim size, again overlap slightly to finish with a straight edge, secure with thread and cut off. Attach your brim to the crown with glue. Ribbons and flowers are all that's needed to finish.

Instructions for gluing - The same principle is followed for gluing but you will need to overlap slightly To work the brim, cover the card with cling film (saran wrap?) and glue the straw into a circle.

For a bonnet, you will have to work a brim with the crown on the cork, working from one position around the crown bottom, leaving a gap of about 1/2 inch turn the straw back on itself and sew around to the other side. Turn back the straw again, doing this four times. Each time gently pulling the straw into a 'curved upright shape' The straw can literally be pulled into any shape when it is sewn.... The fifth row, turn back and finish the ends at one side. Now iron the hat, this seals the glue. Add ribbons, flowers, feathers to finish.

Hazel Dowd


Grunge Mops: A wise lady. Mary Wrenn.. once told me, "When I make something I have it in front of me", and that is what I now try to do with everything I recreate. So for my mops, Cut a 1/8" round wooden dowel into 4 1/2" pieces. Sand the end that will show. Slightly round it. Make a thin, thin wash (like ink) of Raw Umber acrylic paint and brush on the wood. Let it dry, or hasten the drying process by drying in and oven or (as I did) with a heat gun. For the mop head I used a crochet thread. Size?..well the label says..50g (?) It's a bit thicker than darning thread. But I bet darning thread, or white cotton string would be good too. Cut a piece of thin cardboard to 1 1/4". Wrap the string loosely around it 50 times. Take string and keeping the loops together glue them around the unfinished end of the dowel. Cover about 1/4". I used hot glue. Now just under the loops you have attached to the dowel, and about 1/8" from the top of the loops, wrap a string around the mop strings. Go around about three times and tie. It should really be looking "mop like Now cut the loops open on the unattached end. Now for the mop head grunge. I use a very watered down India ink and a touch of the raw umber. Test your color on another piece of string before you dip your mop head. o.k. you have your color (now the fun!) dip the mop in your grunge mixture! Now dry this. After it dried I gently rubbed the mop head on some sand paper to really give it a "used" look.

Lyn Trenary


Ribbon Roses: You can find instructions for ribbon roses (with pictures)here

http://swallowhilldolls.com/projects.htm - or here - http://www.csolve.net/~minidoll/silkrose.htm

How to make a bow: http://swallowhilldolls.com/bowmaker.htm

Sheena


Scissors - Using the curly end of a 'eye' from a hook and eye (as in sewing) in a black metal, cut off the un-curly end and glue it to a silver metal straight part from the 'hook'. If it is in a sewing box it doesn’t need to be picked up, so it stays glued and together.

Diana in NZ


Making Glass Items - I make glass items using bead making techniques (also called lampworking or torchworking). I taught myself out of a book., and work at an old kitchen table. My original goal was marble making, but once I got that figured out I began experimenting to see what I could do to use up the little bits of leftover glass and dregs of fuel. My vases and inkwells aren't blown glass, they are "core vessels" made by winding glass around a removable core (in my case, the core is the end of the clay-coated mandrel (metal rod) that beads are made on). I use a similar method for my paperweights (hence the little depression in the bottom of each one). I have instructions and equipment list on my website for making marbles--I use the same equipment for my miniatures. The kiln is not strictly necessary for the miniatures, but they will be more fragile if they are not annealed. I do not anneal my mini marbles--they are so small I would lose them in the kiln!

Jane Walker


Dental Accessories: We met a young lady at CIMTA who was selling a dentist set. She might be able to help you. They are called: Favorite Crafts - email: idesign@pathcom.com (they are in Canada).

Susan and Warren Flaks


Previous 10 | Next 10


Page 1004 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)