Auto Detailing Tape: I just read about your trunk project. The tape you're asking about is auto-detailing tape, and they have it at most auto shops in a 4" roll about an eighth to a quarter inch wide. You can also find it at Pearls and other good art and hobby shops in smaller, thinner sizes, for detailing everything from airplanes to fingernails. I'm not sure it would work on your project, because most of what's available is very thin and shiny. One variety to keep an eye out for, though, is the vinyl kind. It's heavier, somewhat stretchy, and more matte looking. E.g., gold in the thin variety has a mirror finish and is like, "WOW" whereas the gold in the vinyl variety is like old gold leather by comparison. Lynn O'Shaughnessy |
Edging for trunk: It just crossed my mind that you might try some duck tape cut into tiny strips. Might work? Susan |
Repainting metal: When things are in bad shape it's sometimes best to start over. Since its metal just soak it in paint remover (thinner) and then scrub off the old paint with a stiff brush. After it is well dry, repaint with glossy or enamel paints that will stick to the metal. I sometimes spray paint on a base coat and then paint them. Deb Laue |
Are you down to bare metal in parts on your little painted furniture? Or is some of the paint just dulled? To even up the shine put a coat of Future acrylic floor polish (that clear liquid stuff) on them with a small paintbrush. By the way -- applied with a lint-free cloth, this is a great protective finish to put over wall murals (full sized)! To touch up where the paint is chipped away, exposing bare metal: lightly sand with an emery board around the edges of the chip. Paint with water base primer (common house paint brand). When dry, paint with acrylic paint. Again, use Future to add shine. Anne Gerdes |
Non-working street lamps: Take the tiny glass balls that come on pipe cleaners in (usually older, inexpensive ) decorations that have seen better days. Soak them in a strong bleach water solution for several hours out doors if possible because of the fumes. The hardest part about this is getting the balls filled with the solution. Wear your rubber gloves and force them under water. Be sure you have good ventilation! Marcie Cumberland |
Afghan: I made a nice looking throw by using a piece of loose, open weave sweater knit. I added trim around the edge and it looks quite nice draped over a chair. Maybe this will help. Of course there are those wonderfully talented people that can knit them, too! Just not I! Earlene Lane |
Mini Pillows: I want to share what we did recently in one of our club meetings. we made mini pillows using fabric that had been lined with iron on interfacing, machine stitched with the smallest stitches, and 3/4th filled with Morton's salt. Our teacher said Morton's was best, because it stayed soft, even if it got wet. We glued the open side closed. These pillows are wonderful. They will hold shape when indented or curved, like they have really been used. The interfacing keeps the salt from leaking out. Mary Ann |
Dried Flowers: Dried flowers work wonderfully in miniatures, along with any other dried naturals, with two reminders - first, if you can, spray them with acrylic after finishing your project OR keep them out of the direct sunlight, and second, most dried naturals, either bought commercially or gathered yourself, come with an impressive array of weevils, moths, and other inhabitants. Inspect each bunch CAREFULLY for webs, caterpillars, hanging or powdery bits, and other creepy crawlies before you take it home. It does no harm to heat them at about 200-250 for a while or invest in a small bag of moth crystals. Put the crystals in a garbage bag with your goodies for 2 weeks and you should be "out of the woods," so to speak. I use dried flowers often and find that our Creator does a much better job of keeping His creations in scale than I do. Rebecca |
Stringing Beads for Miniature Jewelry: One wire I like to use in jewelry making (and that fits #24/o beads) is #34 brass. It comes in either small spools or cards and sells for about $2 in many U.S. craft stores. Even better, though, is #100 silk thread, which we in the U.S. import from Japan, and which is hard to find here. (Most of our silk thread is the thicker $50). It makes a nice, flexible strand of beads, and gives a more realistic effect than wire. To pick up the beads without a beading needle, just stiffen a couple of inches of thread with zap-glue to make a self-needle. Lynn O'Shaughnessy |
Tip for Old Shoe Soles: I was just making a few pairs of old boots and shoes. Thought that this tip on making soles for them might be of interest. This is good for either sculpted baked shoes or leather shoes that are constructed on a form. I spread a thin layer of puff paint on the bottom of shoes. Then I hit it with a heat gun. It will puff up in an irregular pattern. Continue to use the heat until paint is dry. Then gently press sole on to a flat surface till sole evens out. To make really old shoes, when spreading the paint keep it off of one small circular section at the front (toe area). When everything else puffs this will remain flat. Then paint this indented area with a light beige/gray. Really looks worn. Hope this is clear. Lyn |
| Previous 10 | Next 10 Page 1025 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |