Yellow Rain Coat: How about cutting one out from a rubber glove, the kind used to wash dishes? It could be cut out in the shape of a coat and then draped to fit to hang. Seems to me that the rubber gloves are very pliable and could be arranged the way you want. Don't know if clear nail polish could be applied to make it shiny. Donna |
Butterflies: For butterflies I use vellum stationary paper. You can use acetate too. Fold in half and cut out half butterflies. Glue a piece of wire in the middle of the butterfly and when glue is dry, paint the butterflies with markers or glass paint. Judy K |
Cat House: many years ago the late Dennis Waldron published some ideas for pet toys, including one of those carpet covered tower "condos". It's hard to describe without drawing pictures, but here goes. Take a toilet paper roll and cut it to whatever length you think appropriate. Trace around the roll and cut out one circle of lightweight cardboard (cereal box, etc.) one inch larger, and another 3/4 inch larger. The larger circle will be the base. Mark a spiral on the smaller circle, from the outer edge to the center circle, going maybe two thirds of the way around the circle. This will be the ramp that wraps around the center core, and the circle from the middle will be the top of the condo. (Close your eyes and think about this, and you might be able to "see" it.) Cut a piece of self stick felt for the base, but remove the center "hole" before you stick it to the cardboard, so the core will fit into it. Test fit the spiral ramp, and cut doors into the core in the proper places. Glue the core in place, and cover it with felt. Trim a scant 1/16th inch from the spiral, and cover it with felt on both sides and glue it in place. You can get really clever and put in a floor or two at this point, then cover the top with cardboard from the spiral and the circle of felt you cut from the base. Dani |
Ceramics: If you want to repeat something many times you can use a plaster mold and low fire liquid ceramic slip. Some molds are 1, 2 or many parts. Open molds you just pour in the clay and it begins to set up. When it is as thick as you want you pour the remaining slip out (and reuse it). For 2 or more part molds you put them together and rubber band them tightly. Then you pour in the slip and do the same as the open mold. When the clay in the mold gets to a leather hardness it has shrunk enough to come out easily. This is the best point in which to clean up the mold lines, thin the lip, and do anything else you want to with it. When dry, you fire it to cone 04. There are many other things to know about (i.e. porcelains, etc.) but this was the fast answer. Jacqui, in Hilo, Hawaii |
Releasing Clay from Molds: To release polymer clay from your bunny mold, you may be told to use talc, baby oil, pam, etc. But the simplest solution is water. Spray a fine mist of water into the mold, press in the polymer clay, and gently remove the bunny from the mold. Mary Eccher |
DREMEL MULTI-PRO: You can get attachments from http://www.dremel.com and other information too. Try their "Owners Club message board" for tips & questions. Also, two very good places for accessories & attachments are: http://www.micromark.com & http://www.widgetsupply.com They have saws, and all kinds of things to make furniture, etc... Nancy in Ohio's husband, Joel |
Dremel Video: Bob Scott, of Lilac House, put out a video (it was done by Mindstorm) in which he shows very clearly some of the many things you can do with a Dremel in building miniatures. His address is Lilac House, 2122 So. Thor, Spokane, WA 99223, 509-535-2917. I don't know if the tape is available any more,but he might be willing to copy his copy for you for a fee. It is very clear with a lot of tips about why you do things the way you do. And he makes for sale a saw that uses the Dremel as a power source. It works very well and is just the ticket for anyone wanting to build furniture. He also recommends S.H. Goode & Sons for wood. I have seen the wood that Goode does, and it is beautifully done. They are at: PO Box 5161, Torrence, CA 90510. Hope this helps and hope he still has some tapes available. Mindstorm might have some of his tapes still left and, if so, they would be available through Mindstorm Productions, http://www.mindstorm-inc.com. Jeanne, San Anselmo, CA |
"Lift Off" transfers photos: I have a bottle of a product from Bond Adhesives Company called "LIFT OFF Transfer Medium". It says that it "transfers photos and prints to any surface such as wood, glass, metal,canvas, ceramics, etc.". I bought it a long time ago and have never actually tried it. I can't tell what store I bought it in, but they used hot orange price stickers. It came in a 4 fl oz bottle. Debbie Olsen |
Free Glue Guide: I found something in AC Moore's which I would like to share with all of you. They have a display of free brochures from Aleene's and the brochure is really quite helpful. It gives a brief note of use and properties of each of the 30 Aleene's adhesives. One panel of the 3-fold brochure has a chart which lists their adhesives, broken into categories, down the left side and across the top are different crafts. Under each craft, there is a dot across from the adhesive that could be used for it. Neat. Go get one before they are gone. After posting about the free Aleene's Glue Guide, I noticed a web site listed in small print (of course) on the back and I checked it. I think it is a site many of you would find helpful. It has sections for sharing (posting with Q&A), Fabric Crafting, Craft Painting, General Crafting, Paper Crafting, Kids Crafting, and Product Location. Did you know that a new paint called Tulip Ultra Soft Fabric Paint is available? It is produced in 3 finishes: Matte, Metallic (pearlized look), and Velveteen (gives look of velveteen fabric). There are a lot of possibilities in that paint for the creative dh enthusiast (like your average ss member). The site address: www.duncancrafts.com Mel in Ma |
NAME: I'll just add my voice to the others on this one. As far as your "skill level", I think you're thinking of IGMA where you can become not just a member, but an "artisan" or "fellow" by applying for these various levels and having your work judged. With NAME, you're just joining with thousands of other miniaturists (some very, very skilled, some brand new amateurs) who love all things miniature. I think some of the 2-day workshops at the annual National convention probably do cost $300 (not always), but at that same convention there are one day and half day workshops that are quite a bit less (this year I think all of the half day workshops are under $100). There are also regional house parties and state days which are not as big a "deal" as National and they also offer workshops and are lots of fun. Registration for any of these events is more than the ticket to a miniature show, of course, but at National there are three meals included in the price, you get absolutely beautiful "surprise" souvenirs to take home, there is a "tote bag" full of favors donated by other members, a wonderful souvenir book with projects for DIY, etc. The Miniature Gazette does come out six times a year now and the quality is great - lots of pictures of members projects (including yours if you send them a photo!), lots of DIY projects, and of course news and calendars from around the country. Some miniature dealers offer a discount to NAME members and if you go to a miniature show which is put on by a NAME club, you get a discount on your ticket. Molly Cromwell also offers discounts to NAME members when they attend any of her shows. And they have a video lending library with, I think, around 80 videos concerning miniatures and they are yours to borrow for the cost of postage ($3.00)! So for $28. 00 a year, I don't think you can do any better. Mary Lynne |
| Previous 10 | Next 10 Page 470 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |