Probably the major difference (besides composition) between tacky glue and Elmer's is that Elmers' will cure hard while Tacky remains flexible. Pour out a gob (that is a very precise measurement) of each on scrap board. Let them both cure for a week or so. Then hit them with a hammer. The Elmers' will shatter, while the tacky doesn't do much of anything. In order to obtain much strength with Elmers', it is necessary to clamp the two pieces while the initial curing takes place - 20 minutes or more, depending on temperature and humidity. Tom |
Moveable glue for use instead of Mini-hold or Blu-Tak: I use Moveable glue for small items I sell at shows like hats and small leather items. These are usually displayed in a Plexiglas case. I apply a few coats of Moveable glue to the items and let dry, then I adhere the items to the shelves. This allows the shopper to handle the items and put it back and once it's back in place, I can pack the case and ship it back home with all the small items intact. I don't know if it leaves a mark on fine furniture. I have used it on the soles of my lil folks shoes and placed them on my desk which has a glossy finish and it doesn't leave a mark. You may want to try this product. Pearl Jordan |
Gluing plastic bricks: I have used plastic bricks and glued them with Elmer's carpenter glue. Carol |
Window Screens: I use a black tulle for screens. Fannye in TX |
Screen windows: In a camping goods store they probably sell no-see-um netting. That has very close together holes and might look OK. I'd also walk though the embroidery section of a sewing or craft store and look at the backing choices for that (you might need to dye the stuff to the color you want). Carolyn |
Screen windows: Karen’s Minis has some screening, you might want to check her out. I don’t know if her website is up and running yet or not. The Phone number I have for her is: Karen (505-532-0939). Joni |
Sharpening Chisels: Joy had a question on sharpening a set of new chisels. Since there are whole volumes on the subject, I will only touch on the basics here. The side of the chisel blade that is flat from the tip up to the shaft does not get sharpened. The opposite side, which has a relatively short bevel is the face that gets all the sharpening attention. This bevel usually gets "ground" on a machine grinding wheel. This produces a concave bevel which is far easier to hone or sharpen, because there is far less steel being removed by the honing process. The bevel has two components; the "toe" and the "heel". The "toe" is the very tip of the working end, the "heel" is the rearmost end of the bevel. Even if the bevel has not been previously ground, the same sharpening principals apply. Ideally, the stones used would range from moderately coarse to very fine in texture. The idea is to obtain finer and finer "scratch-lines" as the sharpening proceeds. Use a light lubricant on the stone, I've seen everything from spit to specialized honing fluids used- so you can be creative. ( I personally recommend just a little soapy water) The idea is to "float" the particles of steel from the stone, preventing it from getting clogged. With the face of the bevel flat on the stone (toe and heel always touching) and both hands on the chisel and out of the way of the business end, attempt to "slice" the stone in a slow steady stroke the full length of the stone. This may take a few minutes of stroking the blade to get it sharp and usable. We take our chisels to 6000 grit and they are shaving sharp. Use a light lubricant on the stone, I've seen everything from spit to specialized honing fluids used- so you can be creative. ( I personally recommend just a little soapy water) The idea is to "float" the particles of steel from the stone, preventing it from getting clogged. With the face of the bevel flat on the stone (toe and heel always touching) and both hands on the chisel and out of the way of the business end, attempt to "slice" the stone in a slow steady stroke the full length of the stone. This may take a few minutes of stroking the blade to get it sharp and usable. We take our chisels to 6000 grit and they are shaving sharp. Brian, Roundwood Studio |
mini router: Dremel makes 2 styles of routers. One is a router shaper table used in conjunction with the Dremel rotary tool. This is the one I use and I’m very happy with it. You can get a set of router bits also from Dremel. I’ve made several items of furniture using that set up and it works beautifully. They also make a hand held attachment that I also have but don’t use as much as the router/shaper set up. Joni |
Screen windows I found the neatest ribbon at Michaels a couple of months ago. I bought it for just that reason to make mini screens. It is 2 inches wide and looks like wire mesh and looks like the perfect sized mesh for a dollhouse window too. Actually, I just measured it and it's 2 1/2 inches wide. It says it's 70% metallic and 30% nylon. It's 10 yards long. I had been looking all over for something that would be just the right sized mesh for a dollhouse window and finally found this ribbon. Cheryl in TX |
Miniature level: Island Crafts makes one. We carry it. Tom Berkner |
| Previous 10 | Next 10 Page 476 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |