Bricks: I used this method to make the facade of a local masonry building before it was torn down. I needed brick walls in a couple of places. First I carved bricks into a sheet of 1/8" thick basswood. I sealed it with varnish then covered it with plaster of Paris to give it texture. I gave it a final sealing with a fixative. Over this I painted many layers of liquid latex. Once it all dried well I removed the latex and poured in plaster of Paris. I repeated the casting process until I had several dozen sheets of bricks about 3 inches high and six inches long. I cut out every other brick on each end so they would finger into the next sheet. I glued these bricks to the plywood wall with liquid nails. After the wall was built I cleaned up and aged the bricks then painted them brick color. (Use acrylics, they soak into the plaster best. To get a good brick effect I did not paint all bricks the same color -- some are darker than others. After the paint has dried well I gave the bricks a coating or Flat Deft spray. When the Deft has thoroughly dried I spread in the mortar and wiped it right off. The mortar will dull the gloss of the Deft.

Bill Hudson


Bricks: you do not seal the plastic brick sheets before painting. It's plastic so the paint won't sink into it. Just spread the grout color onto the brick and wipe it off immediately. Then make a pad of cloth or paper towel, dampen it, dip a color, tap excess off onto paper towel and dab all over the bricks. Use several colors this way, even some dull green, and you will be amazed at how well they look.

June in London, Ontario Canada


Bricks: For a real brick idea on foam core I would suggest: just paint and sand. I did that on my house. It's a lot of work, but when done it looks beautiful. First 2 a 3 layers white paint, then a layer of thick red-brick paint. Immediately after the last layer, blow the sand in the wet paint till it drowns (sand will be red too). When the red layer wit sand is almost dry, scrap away the parts to simulate the joins with a not-sharp thing, an embroidery needle for instance.

Marina from Holland


Aged Tile Floors: Suggest you lay your tile as per normal. Determine positions of appliances, tables, etc. Scuff floors a bit with fine emery cloth over probable traffic patterns where glaze will have been ground away. Don't forget extra wear in front of sink and stove and under the table at specific seat locations. Rub in a bit of lamp black or dust from charcoal briquettes. Clean up the black as best as you can and overcoat with a lighter color grime. (Cigar ash works very well). Clean again. Work some appropriate stains into grout. A bit of rust color from under the sink and darkness of damp near an outside wall. When all is beginning to look old but cared for, cut out one or two tiles and replace with very nice new ones. A cracked tile under a stove leg is reasonable to expect and certainly a heavy bowl or something has been dropped from the kitchen table to crack another. Finish with an eggshell or semi-gloss topcoat and then blend a high gloss of the same brand along edges and obscure corners where there has not been heavy use or traffic.

Mel Koplin, Las Vegas


Aging Floors: To add age to your floor, use "antiquing gel" it is sold at most hobby supply stores in the paint section. Its very easy to use, and water based. You just brush it on, let it set a couple of minutes, then wipe off.

Sloan


Aging Floors: I also wanted an aged look to the kitchen floor in my farmhouse. I used brown wax shoe polish on the floor and then wiped it off. Gave it a softer look than stark white. Wax buildup?

Shirley in Kansas


Aging Floors: For aging the floor, if it is wood, try a few coats of tea. Worked well for me.

Dr. Bob


Aged Tile/Wood Floors: I decided to use the peel-and-stick tiles. I picked some up at Lowe's yesterday - - VERY cheap! And it looks great. If I didn't know better, I'd think it was real marble. It went very well as I used a paper cutter to cut the tiles into 1" squares. One tip for anyone else planning to try this, lightly sand all of the edges of each tile before installing. They look much nicer. I also got the floor done in the attic "store room". I used a wood floor and aged it by denting it with the blunt end of my craft knife, then scratching it. Next, I added stain, and aged it some more. A little antiquing gel along the edges, and to add some "stains", and its done!

Sloan


Stone Floor: I am doing a stone floor. My method evolved because I am actually incapable of leaving anything alone. First I bought 2 Vinyl tiles for 55 cents (Canadian) each. They look exactly like stone. But, being me, I thought "what would it look like if I cut out the stones?" So I cut the tile into random sizes of flagstones. The trick to this is that you have to round off the edges with a file. It looks much better.

Then lay out a grid on a piece of square illustration board, or whatever you have on hand. These tiles have a sticky backing, so you just lay them down in a random pattern, but keeping them more or less straight to the lines you drew. Finally, I outlined each slab with a permanent marker. Doing them on a 6 inch square means you can do this while watching television or whatever you do and it doesn’t seem so daunting as trying to do a whole floor at once with your head stuck inside a tiny space.

I am going to try spackle or caulking as a grout, don’t know yet, but I did not use a spacer when I stuck them down and will just fill in the odd spaces. This looks exactly like a flagstone floor, needs no expensive finishing, and the tiling is easily cut with a pair of scissors.

Doris Tie


Contact Paper: I once used contact paper that looked like the old linoleum and was really happy with it. Unfortunately it was one of the things I lost in the fire and can't find the same. I don't know if the new stuff that is repostional would work, I looked at it once and didn't think it would stick. I also used paper (bought not printed from computer) in a 144 house and just covered it with nail polish because I wanted it shiny. It is still looks nice some 20 years later.

Kathleen in Colorado


Previous 10 | Next 10


Page 496 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)