Separating carpet/wood: Tricia asked: >>I'm not even sure what it's really called, but what do you use on the floor to divide carpeting/wood flooring between doorways? In my real house, it's a brass strip of some sort.<<

I use wood strips, flat on the bottom, rounded on top.

Carol


THRESHOLDS: A threshold is usually made of the same wood as the floors, and is ideally the same width as the door jamb. It is a piece of wood which lays on top of the floors to hide the joint between rooms or types of flooring. It is beveled on both sides to prevent tripping or stubbing one's toe. You can find beveled oak thresholds ready-made at most hardware / building stores, if you want to look at one.
The metal strips are a modern version.

Hilda


Carpet thresholds: I've used the foil cap liners from yogurt tubs rolled into strips, cut to fit the doorway, and sprayed gold (the thresholds in my big house are brass), with snipped-off sequin pinheads for the screws; just tacky-glue into place. The yogurt foil has just the right texture.

Loretta Sniarowski


Bricks from balsa wood: If you have the thinnest sheets of balsa they will cut like butter with a craft knife. Also excellent for making internal wood paneling. Just make sure you mark them up very carefully so they are all as near as poss. the same size because any slight variation shows up large in this scale and you end up with sloping walls!
2 other suggestions, both using compressed paper egg boxes:
1. Instead of balsa, which IMHO is a bit smooth for bricks, use the flat top of egg boxes (12 pack size is best) This gives a textured effect which is much more brick-like. Takes paint much better too. If you would like more info on my method with this, mail me privately.
2. Cover the whole outside of your dh with the flat bits of egg box and then cover the egg box with brick paper, Scribe the mortar lines gently with a blunt instrument, e.g. the end of a small paintbrush - this gives quite a realistic brick effect, again with a texture.
Either way you'll need a lot of egg boxes - enlist your friends, they soon get used to strange requests from their miniaturist pals!

Chris in Scotland


Making Bricks: I tried using balsa wood to make bricks. I got a wood stripper from MicroMark, to slice the balsa sheets into thinner strips. I found that as I tried to cut along the grain of the wood to make small strips, the wood grain often pulled the knife blade one way or another. Result - wavy strips of wood.
Our club did a project where we made our bricks out of cardboard. Here's the technique we followed, as best as I can recall:
Go to a Dick Blick store or other art supply store and buy acid-free matte board. As long as you're going to invest the hours of painstaking work into this thing, you'll probably want it to last a good, long time, and going acid free will reduce degradation of the cardboard over time. Paint the surface of the cardboard the color of bricks you want. Acrylic paint is fine. (Make sure you vary the color or scumble some extra color of white, black, ochre, or other colors onto some of the bricks so you don't have a cookie-cutter sameness to the bricks, because few bricks are exactly all alike.)
Once you've smeared your paint on a good wide swath of the cardboard and allowed it to thoroughly dry, cut long strips of the cardboard with a metal rule and a rotary cutter. Then, using a "Chopper" (you can set up a fixed template for the width of the bricks and cut brick after brick after brick. Next, glue your cardboard bricks to the house using QuickGrab glue. It's waterproof and the bricks stay where you put them almost instantly.
Now... before you grout the bricks, mix a diluted solution of white glue and water and paint all your bricks with this. If you don't seal the bricks and especially the sides of the cardboard bricks, the moisture from the grouting can cause the cardboard to delaminate and suddenly your nicely painted brick surface comes off in your fingers.
Grout the bricks and carefully sponge off any extra grouting. Grout a small section at a time - no more than a couple inches square so it doesn't harden and "set up" on the surface of your mini bricks.
As with any project like this, you'll surely want to try this method out on a test project - perhaps even a spare piece of plywood - to see if you like the way it works before you commit to doing all 12,000 bricks! Lots of luck!

George Held, Cedar Rapids


Bricks: This takes a bit of patience, but I think well worth the time and effort. When I wanted to make brick posts between the iron fencing around my San Franciscan, I cut very fine sandpaper into "bricks". I painted the wood I was going to apply them to the grout color. Then I began gluing them down. The nice thing is that you can wrap around the corners very easily! OR if you want some irregular bricks, simply cut. When the glue is thoroughly dry, start painting your bricks by lightly sponge painting on the paint. The colors you use depend on the color brick you'd like. I think the sandpaper gives the brick a very realistic look.

Marilyn from IL


Making Bricks. In my first house, I made the fireplace in my living room and it has bricks (the little clay ones) all inside the fireplace. But I bought the other 2 fireplaces... just cheap ones, and the finish inside the fireplace was smooth... no bricks and no room to put the clay ones. I painted the inside all black, cut brick size pieces of the black sandpaper, and glued them on the inside of the fireplaces with space for mortar to be showing (the black paint). Then dabbed black paint over the "bricks" for further soot.

In my colonial kitchen, I made the brick fireplace from basswood. I used a piece of left over plastic brick sheet to draw lines both ways between the bricks. Then I got my trusty engraving tool I bought from Micro-Mark and "engraved" the mortar all around the bricks... as well as sort of roughed up the surface of the bricks by "sweeping" the engraving tool back and forth over the wood. I painted down in between the bricks gray, then used about 3 colors to paint the brick surfaces. I'm really pleased with the look of these "bricks" and, though it took hours to do.

Rita Pierce


Sandpaper bricks: I think this makes great bricks, and it doesn't add to the weight of the house too much. I paint my sandpaper before I cut it out. Use slightly different shades (be subtle!) then, when you cut them out, they will have a less uniform aspect. Acrylic is fine for this, but watered down is best. Paint your wall the colour of the mortar you want before you apply the bricks. Use a guillotine if you can get hold of one. The job will ruin the blade, but it does make it infinitely easier to do.
I do roof tiles the same way, but smooth good quality card, not sandpaper. It takes ages but the effect is very good.

Lynne Connolly


MagicBrik/MagicSton: Years ago, I used MagicBrik on the outside of a smallish two story colonial. I love the way it turned out--and it's so simple. I did dip a sponge lightly in gray and black and tan paint to sponge on some "age". I was thrilled. Just recently I used MagicSlat on the floor or a potting shed room box that I've been working on. I think it turned out great too. Again I used a sponge to color some places of the slate. In both instances, I used the paint to color the texture before I peeled the stencil off. I contemplated many other bricking/slating mediums before choosing this one but it seemed to me that other ways were just too time consuming (and expensive). Keep in mind that I am one of those people much more interested in the inside of the dollhouse than the actual construction!

Magic Brik & Magic Stone, Block, Etc: I have used both the brick and stone products. The entire outside of my very large dollhouse is covered with the brick and I used the stone for the foundation and the inside of the basement walls. If you go over to my site http://fayzerplace.homestead.com/ and follow the link to "My Minis" and 'Dollhouse' -- for a good close-up of the brick, look at the "yards" pictures and you can see clearly what it looks like. For the stone, go to the "basement" pictures. I recommend it. We have used it for smaller projects also for chimneys, etc-- it comes in 1" and 1/2" scale.

Fay in St. Louis


"MagicBrik": I have made a foundation and chimney using the "MagicBrik". It works very well. Here are a couple of things to remember if you use this method:
1) Paint the color of your grouting on the house first and make sure to daub this color with some variations of color (black, white, other shades of grey, perhaps a bit of green on the lower, mossiest side of the house), because the mortar is rarely a consistent color throughout all of the sides of the house.
2) Use a T-square to mark reference lines on your house to help you keep things straight as you work.
3) On the corners, make sure you line the brick mold up so that you have a half-brick (end) pattern matching up with a full brick on the corresponding corner.
4) If your house dimensions aren't exactly right, you'll find you have fractional lengths of brick at the corner which is a bit tricky to deal with.
5) When you peel the template off, be very careful about the bricks - you can easily misshape them or damage them.
(Suggestion - do the project in sections rather than a huge chunk at a time.)

George Held, Cedar Rapids


Previous 10 | Next 10


Page 499 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)