Weathering Brass: You can use Patina-It Weathering Compound made by A-West, Box 1144, Woodstock, GA 30188 to weather a brass wind vane. This makes the brass turn blue like it would after years outside. Alan Hamer, who uses this material, actually leaves the vanes outside in the weather for a couple of weeks after applying the Patina-It. Pam & Pete Boorum |
Weathering Brass: If you want your brass green, I can attest from first hand experience working on a "tall ship" with WAY too much brass, salt water does a fine job of turning it green (rinse the brine off though before it dries or you will have salt spots that are more like not so mini salt candle drippings). Hand oil makes it tarnish quickly (like for example 50 people up and down the stairs holding the rail for 2 hours). Just make sure your brass isn't coated with the anti tarnish stuff as that makes a mess once it starts to wear away. Carolyn |
Weathering Brass: Carrs Modelling Products in the UK do various chemicals for weathering and blackening different metals, or they did a few years ago anyway. Colin Bird |
Paint: what to use and why: I have switched from using hobby paint to using house paint. Results are much, much finer. Judie |
Installing Commercial Doors: I've installed my doors two different ways. I first discovered this problem with another dollhouse I was building, and the house was assembled already. I had a few choice words over that! I tore off the bottom threshold of the door and trimmed the frame as well (about 1/8" off the bottom of the entire assembly). I removed the pin from the door and then drilled a new pin-hole where the pin had been in the bottom of the door and made sure it was deep enough to hold the entire length of my door pin. I also made the hole a little larger than the thickness of the pin, so that it would slip out easily. Next, I drilled a shallow hole in the floor (about 1/8" deep) in the place where the pin would normally come down out of the door into the floor. I slipped the pin into the door, covered it with a piece of thin paper to hold the pin in place while I positioned the door. Once in place, I pulled out the paper and allowed the pin to drop into the hole below. Voila! The door was fastened. (You might need to nudge it a little one way or another with a thin-bladed knife to get it into the hole.) If your house is still disassembled, you can deepen the door hole by the 1/8" you'll need to drop the door down. Keep in mind the thickness of your flooring - you'll want to have your doorway be smooth with the rest of the floor on the inside rooms of the house. A front door will normally have a sill-plate, and so it's no problem to have the slightly rounded wooden barrier at those doors. George Held, Cedar Rapids |
I don't use the commercial doors as they come. I remove the pins and the threshold and install the door using hinges with no threshold (like my real home). If you do plan to use the threshold, I'd certainly sand them down bunches. Like you, seems the little people would trip over something that tall! I always wanted to use hinges as the "real" doors do...except for swinging doors, I haven't seen a real door installed the way the mini doors come. Rita Pierce |
Nail Polish as Varnish: I also wanted to warn about using clear nail polish for finishing, as varnish. My son-in-law is a stock broker and I used his and my daughter's engagement picture reduced down with a cut out of a financial magazine across the top (you know those little stickers we all get trying to get us to buy subscriptions to magazines). Scanned this and printed it out and painted several coats of clear nail polish over it to give it a really glossy look, like a real mag. It looked great! However, I misplaced it before putting it into magazine form and placing in my house. Ran across it about 3 years later and you wouldn't believe how yellowish brown those little mags were! Awful! I don't know if it was the brand (who knows what brand I used now!) or if it was really old when I used it, but I just wanted to warn you about what "could" happen to something you paint with clear nail polish. I'll have to completely redo the little mags and use another glossy finish. Rita |
Icing aka Whipped Cream aka Frosting: Either in a post from a fellow mini-er or on an internet site (Forgive me, I can't remember which at the moment), they used the plastic caps from 2 liter soda bottles for cakes. For icing aka whipped cream aka frosting they slathered on "fake snow" which comes in a jar and is manufactured under different names. For "shaved chocolate sprinkles" on your cake, shave off pieces from a brown crayon. You can also top your cake with "strawberries or cherries" using red seed beads. Karen from PA |
Cream for cakes. Are you looking for something to "pipe" the cake with, frost the body with, or both? Monika |
Broken Egg: Someone sent me a "broken egg" once, I believe it was made with a clear drop of glue, and a blob of yellow dimensional paint for the yellow part. Actually was looking at it just this morning, it was kind of neat:). If the egg was dropped complete (as opposed to a baking accident where someone missed the bowl), then you could create a shell out of polymer clay, or keep an eye out at the dollar store as I saw a package of plastic eggs (colored, but could be repainted) that would be the right size for minis. Kim Bulback |
| Previous 10 | Next 10 Page 500 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |