Free web photo album sites:
Yahoo! Photos - http://www.yahoo.com
click under Photos.
Webshots - http://community.webshots.com/scripts/controlPanel.fcgi

free photo hosting sites: http://www.andromeda.com/people/ddyer/photo/albums.html

The above link is to a site that compares most of the online photohosting services. (It doesn't include web building sites, just photo hosts such as photopoint.)

Webshots: I have opened a new photo album in WEBSHOTS with a Christmas Scene. I like the ability to use larger pictures. Click on NORMAL to get the best sizing.


Mitering vs. coping: I have been reading, with great interest the on going discussions, over last several months, about mitering. I found mitering for inside corners of dollhouse less than desirable. A lot of fiddling and waste to get a perfect joint. No matter how square I made my rooms it posed a problem of making tight joints all the time.

I turned to coping. coping is the best way to do it if room is out of square and a great way still if it is square. First piece of molding goes in without any cut. The piece that miters to it is mitered at 45 degrees, as usual, and then with a fine jeweler's saw blade I cope the miter away, following the contour of the molding. It is best to cope a backwards angle of five or ten degrees or to finish it off with a fine jewelers file. This way the molding fits the contour of the molding already in place. If you do a good job of coping you have a near perfect fit at the corner.

Bill H


Mitering: I have something to add to what others have said about mitering and this is that you hold the flat (back) side of the molding against the wall of the miter box to make your cuts. Since the molding is smaller at the bottom than it is on the top, it means you have to press it against the sides to hold it firmly. Another way is to place the molding upside down in the miter box and make the cuts as though they would be on the floor - but this might be more confusing. They rest in the box a little better because the widest part of the molding lies flat in the box. With a little practice, I am sure you can do it right side up. Just measure first and then draw a line on the top (which will be glued to the ceiling) to show what angle to cut. I always measured the back wall first and then followed with the two sides.

Jeanette in Wisconsin


Wood finishing is a very complex subject: The definitive book is Understanding Wood Finishing, How to Select and Apply the Right Finish, Bob Flexner, Rodale Press, 1994, ISBN 0-87596-734-5.

Pete Boorum


Finishing Furniture: The furniture from that House of Miniatures swapmeet deal is turning out so beautiful. I am very careful now to stain before I put together. I've been using Minwax Wood Finish in Early American. This penetrates, stains and seals. I also bought the Minwax stain marker in the same shade. I used this marker originally when I was trying to figure what shade I was going to use. I used the pen until it was empty, and now I find that it is great, because of the felt tip, for dipping in the stain. Much neater than using a rag for staining.. I've learned to glue carefully when I put pieces together in case I have to touch up the stain later . So far, I like the look of just using this without putting anything over this finish. The finish feels velvety, and the pieces look like fine furniture.

Dolores


Sealer: I don't recommend using Watco as a sealer under paint because I don't know how long it takes for all the oil to evaporate. This is not a use recommended by the manufacturer. There could be an adhesion problem. It is a polyurethane filled mineral oil that is great in full scale but requires sanding between coats which is often difficult in miniature.

BTW be very careful with rags from Watco because they can self ignite and cause fires. Always put rags in a jar or can filled with water or directly into the wood stove. DON'T EVER PUT ANYTHING DAMPENED WITH WATCO INTO THE TRASH.

I use Watco almost exclusively in full scale for everything from kitchen cabinets to miniature room boxes. I like it because it is easy, there are no drips and it is a great look with unstained cherry or oak.

Pete


Prime Directive: << Can you paint directly on the plastic with acrylic paint or do you "have" to prime it first with something else? >>

This question answers itself. When you paint on a surface and the paint beads up and looks patchy because it won't stick... you should have primed it. Plastic is one of these things that needs primer.

Laurie Sisson


Painting Plastic: You might find it easier to paint with model car paint (e.g.: Testers) since it was made for painting on plastic.

Viola


Priming Plastic: You need a bottle of Acrylic Gesso (I use Liquitex) it is something I can't make miniatures without. It looks and goes on like white paint but it is slightly chalky and it keys into the plastic and provides a good base coat for acrylic paint. It can be used to prime practically anything - glass, stone, silver, wood .....

It is water based so you can wash your brushes with water – but wear an apron or something as it does not wash out of fabric easily.

Lesley, Johannesburg, South Africa


Tung oil: Tung oil is natural. It oxidizes in the can once opened and has a short shelf life. More than two coats of pure tung oil is not recommended because it may never dry. Tung oil varnish dries better. Tung oil is an ingredient in marine spar varnish.

This is a good natural finish for table tops and would be fine for floors and paneling in a dh. In my opinion it is too thick and hard to control for furniture, but I haven't used any in a long time. About 18 years ago I made a full scale coffee table in cherry and finished it with two coats of pure tung oil. The finish has held up fine. In those days I used it on lots of full scale furniture.

Pete


Previous 10 | Next 10


Page 504 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)