Mother-in-law's tongue: Also known as Sansevieria or even Snakeskin plant.

I made one using wire, masking tape, air drying clay, fine railroader's dirt (the gravel the railroader hobbyists use for landscaping), little pot, paint and glue.

1. Cut a piece of masking tape and fold it over a length of wire, leaving some wire sticking out.

2. Trim the masking tape into "sword-like" leaves.

3. Paint the leaves to match the variety you wish to emulate and let dry.

4. fill pot with air drying clay to just under the rim.

5. Paint top of clay with glue, and dip into the railroader's dirt.

6. apply a little tacky glue to wire sticking out of leaf, and insert it into the pot.

7. allow to dry overnight.

I like the masking tape better than clay because it is a lot thinner and a little more realistic. I believe I used two colors of green (one dark, one lighter) and a cream on mine.

Kim in Canada


Mother-in-law's tongues: Same method as has been suggested for masking tape but a different material!

I use micropore surgical tape for some plants and flowers, including m-i-l-t's

It absorbs acrylic colour beautifully - if you thin the paint, you can get a translucent effect in flower petals.

- For thicker leaves, just use two or more layers of tape.

- Varnish with matt varnish to get the soft sheen on the leaf.

Striped-edge variety looks even more realistic if you include a couple of small leaves which have reverted to pure green without the edge. Or make a few "wounds" in the edges of leaves where somebody has bashed them - I like life in the dolls house to reflect the reality in my real house!

Chris in Scotland


Fimo Mother in Law's Tongue: With a photo or real plant sitting in front of you, mix a ball of each of the different greens you see in the plant. Roll each of the green balls out flat and stack them all in the order you see the colors on the leaves. The height of this stack when pressed together should be the width of the leaves. From this stack cut out a rectangle a bit longer the longest leaf. With the vertical lines of green facing you shape the top of the rectangle so it goes to a point. Slice off the individual leaves using a straight blade or one of the longer blades available for slicing fimo from a hobby shop. Shape the leaves as they look on the plant and bake individually. Once baked stand the grouping of leaves in a some plasticine in a pot and cover the top with old coffee grounds.

Jean Day


Plants: just use the same basic principle as for the MIL tongues for whatever foliage plant you want -- same shape cut with fringed edges makes ferns, or cut the tape to the shape of the leaf you want to copy (helps to have a real one as a "model").

For blooming plants, I like poppies. Good way to use up office scraps when we use red pages as section dividers. Use a dead ballpoint or dull needle to make the red punches cupped. Make a round loop on one end of a piece of wire and blob some tacky glue into the loop. Arrange about 7 punch petals around the loop. Let it dry, then blob another bit of glue over the center and shake on some poppy seeds or black sand (I've used seeds with no bug problems, but the plants are in a sealed glass container). Use bits of green deer moss or air fern as the foliage.

Same principle of recycling round punches can make irises -- cup six petals, cut a wire and wrap the end in another punch for a stamen. Put a line of glue around the bottom of the stamen. Glue three of the cupped petals facing toward the stamen. Let dry and glue the other three petals facing down, away from the previous three. Cut a batch of MIL type leaves and paint them a solid pale green. Stick Iris(es) in pot, stick leaves around outside, and you're done.

Loretta Sniarowski


When to Wire: I put in wiring after the house is put together but before any decorating is done inside. If you're going to do the exterior before installing lighting think ahead if you're planning to have outdoor lighting. For example, I bricked my house and I put in the coach lights as I bricked in order to hide the wires underneath the brick. A good hint is to take photos of the interior of the house after you've put in the wiring so that you know exactly where it is after you've decorated the rooms. Wish I had done that.

Carol


<<What is the difference between die-cut, 3/8" MDF and 3/8" fiberboard? Which would you recommend for a beginner? Does anyone know if castle dollhouses are available in kits?>>

Die-cut is a method of production. I means the pieces are stamped out rather than being sawn. It is only practical on thin materials (1/8" plywood usually). MDF is medium density fiberboard (LWF is now available- light weight fiberboard, but only in 1/2" and thicker). Fiberboard can be almost anything made of fibers, be they wood, straw, linen, etc.

The best houses are made of 3/8" plywood. (should I duck now?). Keep in mind that I may be biased since that is what I use, or maybe that's why I use it. There are a couple of castles available on my web site (look under dollhouses by time period). Earth 'n Tree

Tom Berkner


I don't recall that there actually is an American oak. There are probably over 100 varieties. The most common are white oaks and red oaks. There are also brown oaks and black oaks in the US (e.g. swamp oak). It is very possible to have an American oak that is the color of walnut (or darker). The white oaks tend to be the slightly lighter than pine (almost like ash) but some of the white oaks are a medium brown color, the red oaks are a pinkish color. The white oaks have rounded lobes on the leaves, the red oaks have pointed lobes. Incidentally, only white oak is used for barrels, red oak leaks.

The closeness of the grain is largely determined by where the tree was grown. In poor, dry soil, in a dense northern woods, you get the finest grain. For miniature work, I often will mill the wood from the branches of trees, because the grain is usually much finer.

Tom Berkner


Stucco: I stuccoed the exterior of my first dollhouse using the stucco power made for miniatures. I wanted a blue house, so instead of water I mixed blue paint with the stucco powder. I applied the stucco to the house using a round makeup sponge, which can be purchased several to a package at discount and drug stores. The stucco was easy to apply and looks great.

Mary in MS


Stucco: Use Bin 1-2-3 to cover the paint and then use stucco patch. I use this on a lot of my houses. It's quite easy to work with.

Norma Cevetello


Covering Front of Printer’s Tray: What I did with my printers tray was to put Plexiglas on the front and close it with Velcro. It works great and has for a few years now.

Darlene Hubbell


Previous 10 | Next 10


Page 507 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)