Tile Floor: Several rehab houses ago, I gave Emily's kitchen a fancy black and white checker board floor using a sheet each of black and white fun foam cut into inch squares. Cost a little over a dollar, was easy to lay, looked great. I'm not sure of its lifespan, since I've seen old foam furniture stuffing crumble to nothing, but you could make a paper template of your floor, lay the foam tiles on that, and lay the whole floor in your room without gluing down until you come up with a permanent solution. I've also thought fun foam would make great vintage linoleum with acrylic stenciling or spatter paint patterns. For a glossy vinyl flooring effect in modern mini homes, I've used Big Lots vinyl placemats the same way -- even cheaper at around 69 cents per mat! Loretta Sniarowski |
Order of Construction: I think that when you decide to finish the exterior of your house is a matter of personal preference. I usually do as much finishing of the exterior as possible, as soon as possible. But there are considerations in this decision. Things like whether you intend to put siding on, or if you'll use stucco, or brick, etc. Normally, I will construct the exterior walls of the house, then apply whatever finish I intend to use on the outside. Then, I paint or wallpaper, put in the flooring in the interior, first story, except for finishing trims and windows. Next, I finish the UNDER side of the second floor (this will be the ceiling in the first floor), and install that piece. Then, finish the walls of the second floor, install the flooring, and so on until all of the stories are complete. Likewise, I finish the underside of the roof, which is the ceiling in the top story of the house, before putting the roof itself on. I will normally hold off installing all windows and doors, and all trim pieces, (both exterior and interior) until the house is complete inside and out. It is normally the last thing I do. And, I paint and seal all trim before installing it. However, at times, (like my current dh) that I will install the exterior trim ahead of schedule, to speed construction. But, never, never the windows. The reason for this is that I do not want to slip up and scratch the "glass" with a sharp tool, or otherwise damage the windows. Sloan |
House Painting: I always paint the exterior before I add any doors, windows or trim. I also paint the trim before I put it on the house. Sure makes life easier. Most important, in my opinion, is a good quality primer before you do any painting on any surface, then sanding. It gives a much nicer finish. Suzi |
Tile Floor: When I needed a tile floor for a room I was doing, I took acid free mat board the color of your floor, cut to the shape of the room. Then run an awl along a ruler lightly indenting your grout lines. Then go back over those lines with the colored pencil for your grout. You can then go over the top of it with either a mat finish Modpodge or gloss depending on your preference. I left mine free of either because I liked the look just the way it was. Make sure you get the fairly smooth mat board unless you want a slight texture in the finish, in which case you'll probably need to use the mod podge over the top of it. Kathy |
Tile Floor: For the vinyl type, see if you can find place mats with a finish that would work for your tiles. I have some solid color ones that I want to use for a checkerboard design. I am cutting them with a paper cutter for evenness. For ceramic type tile cut up place mats could also be used, but with space for grout in between. Or, paint thin wood with two or three coats of enamel paint and give it a gloss finish with varathane. I think the tiles should be cut out first, then painted, so the edges are nice and smooth. a thin strip of wood or cardboard can be used to space these, then grout. Lots of work, but I for one think DIY gives a more personal look. Jacqui in Hilo, Hawaii |
Floor: If you want to make floors that you can slide into your house (and out again) you could use very thin multiplex wood (I used 2 mm) or plain cardboard. Make it a tiny bit smaller then the place where you want it. Cover the missing bits with strips of wood (plinths?) that you glue on the walls. This also will hold the floor in place. Marina |
Kitchen Flooring Idea: I just redid my full-size bathroom and was covering the shower window with this vinyl contact paper. It is described as frosted, what it has is small diamond pattern, kind of what you would see on a kitchen floor linoleum but smaller, so I suddenly thought why couldn’t I stick this down on top of colored paperboard to create a kitchen floor? It seems to be of the right scale, textured and shiny like floors. Jeanette |
Sandpaper Shingles: I wanted to share something I just discovered about my shingles that are out of sandpaper. I got some white paint on black shingles. So I took a sponge brush and dabbed black paint on the shingles. Now there is no residue coming off the shingles and I can dust the shingles –something that was next to impossible before. They look great too. Penny |
Coffee Table Book: I just discovered a new DIY project for $6.80 -- a coffee table art book. Currently the post office is selling a sheet of American Illustrators stamps with samples from N.C. Wyeth to Norman Rockwell. Stamps may be too big for a normal scale minibook, but fine for a coffee table art book! So I bought two sheets, one to use and one to bind. Even has stamp-sized text on the artists on the backing which I copied (to allow alphabetical order with text and subject on facing pages). Quick, fun and affordable. Loretta.Sniarowski |
Applying plastic brick to your walls. If your brick is the stiff plastic brick from Houseworks, use Quick Grab. Use according to directions on the pkg. Works great!!! Should mention that these thick, stiff bricks can easily be cut with a miniature table saw. And a miniature jig saw can also be used for curves and cuts that are not straight with the world!! Betty Dann |
| Previous 10 | Next 10 Page 511 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |