Finishing Rough Edges of House: I always cover the unfinished cut edges of the house with 1/16"x 3/8" or 1/2" strips of basswood, and paint the house color or trim color. Fannye in TX |
Finishing Rough Edges of House: a lifesaver for me has been Wood filler (in Canada, it's made by Lepages - can get it at Home Depot - you just fill in all the edges, wet your finger just a little and smooth it all out. You can paint right over it and it looks fabulous. Gives a real nice finished look to the edges. Vi in Canada |
Finishing Rough Edges of House: I cover all my house edges with channel molding and paint either to match the color of the siding on the house or the color of the baseboards in the rooms. Mary Lynne in Huntington, WV |
Painting Metal. Use a metal spray primer then you can paint with acrylics with no problem. Just don't spray a heavy coat or use a air brush with paints designed for metal models. Last choice are the testers paints which I hate using as they don't have a water base and I am lazy about clean up LOL. Anita MH |
Painting Metal. Depends on the metal. If a metal gets an oxide coating from exposure to air such as aluminum or steel (rust). The metal must first be cleared of the oxide. It can be "pickled" in an acid bath to remove the oxide coating and get down to bear metal. If the metal is bar to begin with. a primer coat should be applied. When that is dry then use you paint of choice. Certain paints can be baked onto the metal such as enamel onto copper. This is just touching the surface in putting paint on metal. No pun intended. Dr Bob |
Painting Metal. You definitely can paint metal with acrylics. The word "tole" comes from the French word for sheet metal. The metal must be very clean and primed. I have only painted already-primed pieces, and they are in great shape after years outdoors. Bar Turner |
Painting Metal. I always opt for easy clean up if I can! I have recently purchased and begun using a water based paint for metal, called Dr. Ph. Martin's Metal Craft. It works on everything from wood to plastic to metal! Nice range of colors too! I got it at Michaels, but I'm sure many craft stores carry it. Their website has some really neat links too! Alice Zinn |
Painting Metal. You can clean the metal with rubbing alcohol, prime with Folk Arts Glass & Tile Medium (pay attention to the curing time) then paint with acrylic paints. This is quick, easy and cost effective since it only requires the addition of the medium to your assortment of craft paints. Becky |
Painting Metal: Any paint can be used on metal, even the wonderful acrylics "we probably couldn't live without!" But, the metal must be primed first to prevent rust from forming. With new metal, wash the piece first in soapy water, then rinse in a half/half solution of water and vinegar. This will remove any traces of oily film or fingerprints, and will also give "tooth" to the metal for the primer to adhere. Then, allow the piece to completely dry (if you're in a hurry as I usually am, use your hair dryer to make sure that any accumulation of moisture is out from furled edges, etc.). Apply a rust-inhibitive primer such as the Krylon product or any metal primer found in the automobile section of your hardware store. Again, using a primer gives the piece "tooth" so that the acrylic paint will stick to the project. With old metal, sand all loose rust from the piece and remove any remaining rust with a Naval Jelly. Then, follow the instructions for new metal prepping before applying any paint. Though the piece may be primed, it is very easily scratched before any paint is applied, therefore, care should be taken. Once painted, it's fine, but I always apply several coats of varnish just to be on the safe side. Helen, Boucherville, Quebec |
Chenille Bedspreads: At your request for help in creating a chenille bedspread, I did some searching & was astounded at how many of them are up for auction on eBay. (Ideas!! Ideas!!) If I were making one, I would probably attach a cotton spread to the bed I was making and then add the "chenille" design with puff paint. Some cotton/poly materials have delicate designs printed on them that you could use for a chenille pattern. Good Luck. Anita Myers |
| Previous 10 | Next 10 Page 515 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |