Hundreds of mini links sorted into precise categories for "speedy" surfing http://www.miniaturereality.com/ |
Ink Longevity: Inkjet inks used on regular paper or non treated fabric are not water fast or UV resistant. How quickly the print quality deteriorates depends on the brand of computer/model/ink you use and the actual environmental conditions in your home. For inkjet inks, high humidity is the worst offender, followed by exposure to direct sunlight! Neither are good for inkjet ink printed items...or other furnishings for that matter. However, the good news is that there are specialty papers and fabric treatments that will substantially increase the inkjet printed output durability. If you want custom items that you can't find elsewhere you may want to check out the newer products available for your printer. If you are using your computer to print designs that you want to last it will pay off in the long run to invest in the higher priced papers and the fabric treatments. Computer makers and separate vendors are diligently working to make inkjet ink and specially treated receptive surfaces with maximum durability. The business community, digital photographers, and home crafters markets are very interested and this is a new and rapidly changing field. New products are being introduced all the time because consumers want them. Each computer model is different so you need to check with the manufacturer to see what they recommend for your purpose. For instance, with my particular Epson printer, the manufacturer sells a matte photo quality paper with a factory tested "non fade" time up to 25 years that can be special ordered. This is much better print retention than the generic printer paper at Wal-Mart. To find out what is available or under development for your printer model you would need to contact the manufacturer or a *knowledgeable* office supply representative. For fabric printouts, the T-shirt transfer paper for your specific printer brand, the June Taylor *colorfast* (not just the regular) fabric sheets or the BubbleJet Set 2000 pre treatment will give much, much, more durable prints that simply printing to non treated fabric or generic printer paper. I have fabric and paper items that I've printed with my $150.00 Epson that have no noticeable fade for over several years. But I have used the best special papers and fabric treatments to obtain this durability. It will not be accomplished using generic printer paper or untreated fabric. Also, it is important for all furnishings, even in your full size house, not to expose them to direct sunlight or high humidity. If any of you have ever seen a older home, with wallpaper, a southern exposure room, furniture on the north wall....after a few years, if you move the furniture, you will notice the "fading" on the wallpaper because the wall *behind* the couch on the north wall did *not* fade as much! For inkjet printed wallpaper I would recommend using the June Taylor *colorfast* Fabric Sheets. I would not use generic printer paper. The June Taylor colorfast fabric sheets will be somewhat expensive at $2 to $3 a sheet but if you want custom designed wallpaper that you can not find elsewhere it may be worth it to you. As several others have suggested, you may want to apply the wallpaper with iron on fusible web to a piece of poster board. If the quality does not suit you several years later it would be much easier to remove than if you had glued the wallpaper to the wall. Also, if you have really expensive or heirloom quality miniature collections, you can purchase UV film that can be applied to a Plexiglass dollhouse cover that will substantially reduce the UV fading of all interior furniture fabric and wood. A local interior decorator, or auto restorers' supply shop could refer you to suppliers in your area. Wilma Kinder in SW MO Ozarks |
Hundreds of mini links sorted into precise categories for "speedy" surfing http://www.miniaturereality.com/ |
Stained glass: I came across this site today and thought someone might be interested in it. http://delphiglass.com It is a stained glass supply company with all sorts of tools and stained glass supplies. Spencer |
EGGERY: I found this site that has eggery supplies. I also have their printed catalog because they do have a few things for miniaturists that are useful. I understand you have to cut the eggs with a special saw. Try this site and see if they can help. http://www.TheEggeryPlace.com Carol from Kansas |
Inkjet Longevity: I'm in what I laughingly call my Research and Development (R & D) phase of making wallpaper. Although I haven't the resources to conduct testing on a museum level, I have performed some rather rigorous testing on the things I make. I have to take exception to Tom's statement: "The typical H-P ink on H-P inkjet paper will last 6 months." I have not found this to be true. Since folks are buying my things made on an HP (Hewlett Packard) printer, I feel I must defend the quality of these things. I'm getting ready to buy my sixth HP printer, right now I have three of them. It will be another one to use to make minis and I'm getting it only because it handles larger sizes of paper. It is about five hundred bucks. The number of fabrics and papers I have shoved into my printer are in the hundreds. Usually the consumer is largely unaware that there is a difference in ink formulations, even among models from the same brand of printer. Two of my printers use pigment based inks, one uses thermal inks. Expensive prints such as those you can have made, usually use a process called dye sublimation....those inks are different too. It is the INK that fades, so if fading is a concern, then it is the ink quality...the properties of the ink, that you need to take into consideration. What you print on...also has it's problems. Paper will deteriorate with nothing at all printed on it. Generally the consumer is also unaware that some papers have a right side, and a wrong side. The formulations for paper are almost limitless. The papers Tom is talking about are available to the consumer; Unfortunately, you have to buy a WHOLE BUNCH of it. But nothing keeps you from cutting it with a paper cutter and feeding it through your printer. Most home printers have a maximum size they will print of 14"long...unless you lie to it and tell it you are printing a banner. However, you are almost always limited to 8.5 inches wide, with a print area of 8 inches, and 11 inches long with a print area of 10.5 inches. Most dollhouse ceilings are less than 10.5 inches, and eight inch widths would probably cover most walls anyway. If the image was turned sideways, it would print eight inches tall, and ten and a half inches wide. Don't the inexpensive tab and slot kits have eight inch ceilings? The way I go through my "testing" is to print on a variety of surfaces, put them into varying degrees of direct sunlight, and or...put them away in a box for six months or a year. I also make prototypes of the mini thing I intend to use the image for...and use a number of adhesives on it, and put this away for awhile too. I have discovered that it is usually the adhesive or the sealer that causes chemical reactions and makes the image blur. Not the ink. And not the paper...if it didn't blur within a few days of being printed, then it didn't ever. What makes the water based inks in inkjet printers blur...if it isn't the sealer, or the adhesives...is moisture. Moisture is death to ink jet inks. The transparency material has a coating on it that will absorb moisture and is not very good in any kind of humid condition without being protected somehow. This is probably what caused the church windows to blur. And...Tom said "over the years" they have blurred. The inks for home printers has improved in quantum measure from "years" ago. Tom suggests that you inquire what inks and papers are used for things you decide to buy. This, on the surface, sounds like a good idea, however, some materials and procedures are trade secrets to some manufacturers. No manufacturer, including me, knows the "expected lifetime" of printed things for sure. Even the museum research is still in progress. I can tell you how long they have lasted for me...which so far is five and a half years for some things, without any special care. Having a printer print your wallpapers won't guarantee heirloom longevity. Printers are who also make those prints we have seen hung on the wall at the dentist's office, or in some Motel Six somewhere, that have faded to pale pinks and blues in only a couple of years. You can get great results out of your home printer. I haven't found the things coming out of my printer to be particularly fragile, or temporary. If it is an heirloom you are creating, then maybe paper for the walls isn't the way to go anyway. Don't be dissuaded from making your rugs, and wallpaper, and stained glass windows if you want to. They will certainly last as long as a tiny ottoman made out of a toilet paper tube. For all things in your dollhouse to last the longest...keep it away from the kitchen, and the bath, out of direct sunlight, and out of cigarette smoke and you should be able to keep it nice for a long time. Terry |
Ziplock bags: Science and Surplus http://www.sciplus.com also 1-800-934-0722 Itty Bitty Ziplocks Item 90273 Poly bag 1 1/4" $1.75 /bag of 100 90274 Poly bag 2" $2.00/bag of 100 27906 poly bag 2"X3" $$2.25/ bag of 100 They do have a merchandise minimum of $10 but call and get their catalog or go to their web site I'm sure you will have no problem spending $10 Marsha Hedrick |
Starfish, Seashells, etc: Here is an answer to the question on where to find tiny starfish and sand dollars. Go to http://www.seashells.com This is the site for Sanibel Seashell Industries. Carol from Kansas |
Art Deco Furniture Patterns: I have one of Peter Wescott's Mitre Box Series plan books, "Art Deco Furniture Patterns, Vol. 1 (1996). The patterns included are for a bookcase, storage cabinet, side board, bed, dressing mirror, dining chair, small desk, dining table, storage unit, dresser. The designs are excellent. His address is listed as 6256 North 85 Street, Scottsdale, AZ 85250. No phone listed. Maybe someone else on SS has info regarding phone number and possible web site. His series of pattern books includes Mission (vols. 1 & 2), Southwest (vols. 1 & 2), Shaker, Contemporary, Colonial, and Porch & Patio. Marilyn - Wisconsin |
Art Deco Furniture: Someone was asking about Art Deco Furniture. Have you tried Mathew Damper: http://www.matthewdamper.co.uk/ Colin Bird |
| Previous 10 | Next 10 Page 523 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |