Removing Super Glue Fume Haze: I made a miniature Christmas tree under a glass dome last year and put the dome on too soon and ended up with that haze, also. I removed it with rubbing alcohol. Rubbing alcohol also works on Plexiglass.

Carole


Big Screen TV: Pick up a clear plastic jewel case for a zip disk. If you look at it on the side where the ridges are, (hold it so the ridges are at your left and right) you can envision those ridges painted black, as speakers. Paint the rest of the jewel case black or gray/silver matte then glue a TV picture in the middle. Place your TV on a slender wood or another base and you've got a large, slim and flat TV screen. It's very believable.

Leslie Ann, CA


Umbrella: You could get one of those cocktail umbrellas used for fancy drinks. Remove the paper covering and replace it with a cloth one.  The size is a bit large for 1" scale, so would probably do quite well for your bear since it is bigger.

Viola Williams


Bolsters: Another idea for bolsters is the sponge hair rollers.  They come in a variety of sizes and I liked them because after wrapping the fabric around them, you can tuck the gathered ends into the hole that is at each end of the rollers. (Of course you remove the plastic "clips" first)  Then cut a circle from pellon-backed fabric, and glue it over the ends of the rollers.

Viola Williams


Woven Rugs & Bead Spreads: I am a hand weaver who specializes in miniature rugs & lace bedspreads. My original designs are woven with fine threads of cotton, wool or silk. Many are one-of-a-kind. http://weaver.iwarp.com

Lili


Painting previously painted surfaces without sanding: There is a product called "No Sand" or something like that and it is just used to dampen the surface of a painted or vanished surface and then you can paint. It works chemically to soften the previous finish so the paint will adhere. I have used it with great success on full size stuff, should work on minis. It is in the paint section of Walmart and home improvement places by various names.

Susan from St. Croix


Barrels: If a barrel is made properly, it doesn't need any nails to hold the hoops on. They (the hoops) were usually put on hot, like a wagon tire, knocked down (put in place,) and cooled quickly by pouring water on them. Wine or liquor barrels do not want nails protruding into the wood as it will contaminate the wine. Even if the nail only penetrates three fourths of the way, the wine will soak into the wood and draw out the contaminate.

Hoop nails were used on shipping barrels and kegs (as used in shipping dishes and stuff by freight wagon or river boat.) These nails held the hoops in place during the rough handling of the shipping and travel. The nails had a one sided head somewhat like a railroad spike, only much smaller.

****HINT***To make little hoop nails, file three sides off a small brass nail and flatten the head a bit. Push it in so the one side of the head fits over the hoop. If using brass nails, blacken them with some sort of blacken. I find the stuff you get from a stained glass shop works quite well and in the long run much cheaper than the hobby or model RR stuff.

***HINT ***A nice touch.Make your barrel and install the hoops. Stain it, then remove one or two end hoops and shorten them or make them longer so they do not fit back in same place. This will show the unstained area which will look as if the hoops had been reset on the barrel. Some times if a barrel was not used for a while, it would dry out and a hoop would loosen up. To make the barrel useable again, the hoop needed to be reset. This was done by heating up the hoop and driving it back on.

Bill Hudson


Southwest Courtyard: I have a Patio/Courtyard on my web site, click "room boxes".  It can be adjusted to your dimensions.  I also have access to accessories for your project.  Please e-mail me privately for more information. http://TaosSunMiniatures.com

Spencer in Taos, NM


Roughing Up Log Cabin: I have uses a wood burner to great satisfaction in making wood grain and roughing up dowels to replicate logs. First you need to uneven up the logs a bit. Use a small hand plane to take off some of the round. Then a heavy rasp. Drag the rasp side ways along the log. let it wobble a bit as the grain isn't always in line.  Then go back over with the wood burner to highlight spots.   to make a knot drill a hole in at an angle and drive a whittled small round dowel to make the knot. Chop it off a little high. Then with the wood burner burn the end of the dowel to look like a dark knot. Then using the wood burner burn in grain lines around the knot.  It should look something like an eye. After all this You should stain the wood to look old.  I even like rubbing ashes in the wood after stain it and then wiping it off.  Famous Thomas Bug juice also works well for darkening the wood. Not so well on pine but it does work some.

Bill Hudson, Eugene, Oregon


Clay Gun: I have really gotten a lot of use out of my clay gun for Fimo, it is sometimes called an extruder. It's wonderful for so many things. The clay should be quite soft, I sometimes even put it on the ground and use a foot on either handle and push the Fimo out, this works really well and doesn't hurt your hands. The circle and square shape is good for making jars- extrude, bake then slice. The flower shape you can extrude, slice and shape into petals. The screens are good for hair and the thin rectangles can be formed into bows or woven into baskets. I've extruded the small mesh screen circles and made wreaths by twisting the lengths. The ribbon one I have used for siding and shingles on mini bird houses and for the handle on a watering can. Hope this helps you with your decision.

Jean Day


Previous 10 | Next 10


Page 526 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)