SW Printables: here are some western / southwestern boarders, I found on the web. I think a couple of you were doing that style house and might like to use these. http://members.nbci.com/_XMCM/BluvW/projects/printables/wallpb/w_west.htm Jane Rezza |
Nautical Accessories: For the person looking for little bottles, I don't know if they are still out there, but years ago I was able to obtain little glass bottles that were the correct size for small water coolers in mini- would have been about a bit more than 1" tall.. They came from a friend that worked at the hospital, I believe they were some kind of medicine vial. Maybe someone on the list who works or knows someone who works in a hospital can check it out for you. Hallmark has put out two great ornaments in its miniature ornament series that would also be good for your nautical minis- they are little bottles with lighthouses inside of them. It is part of a series, they had them this year and the year before. You might be able to find them on eBay- I'm betting the stores have sold or put all the Xmas ornaments away. Michael's also has some wooden unpainted nautical stuff that might be a possibility. I saw a rowboat that was pretty nice - maybe not perfect scale, but not bad either. I built a 3" lighthouse and light-keepers cottage for use at the floral shop I work at. They had a table setting contest complete with decor and flowers and ours was "New England Brunch". I built the basic lighthouse from foam core, spray painted it with gray fleckstone, and then taped off stripes and painted them black. The lighted top was made by inverting an appropriate sized glass jar into the base. I used pin-striping tape from the auto store to simulate the panes of glass, and put in an electrical socket with a yellow bulb and blinker. The cap on top of the glass was an old chandelier ceiling plate and a decorative knob. I also built a railing around the "light". It cost under 10 dollars to make the whole thing. Bonnie Gibson - Tucson, Arizona |
Empty Bottles: Bits 'n Pieces has lots of excellent glass bottles on her site. Some are from England, others from Glass Blowers Workshop. http://BitsnPiecesOnline.com Anne Gerdes |
Empty Bottles: The web site where the bottles are located is http://hometown.aol.com/GLASSMURPH/index.html He does sell retail. Carol |
CROWN MOLDINGS I presume that your difficulty is with upstairs walls that "slope" because they represent the interior side of roof slope. If you want to put crow moldings on such walls, you will have to first install a wedge shaped "sub-molding". The idea is to create a molding-wide (vertical dimension) block that is vertical. Use a protractor, goniometer, bevel square or whatever to determine the angle you need. Use a table saw (if available) set to the desired angle to rip a long triangle shaped strip from the edge of a 3/4" thick piece of pine or similar. Mount these strips as though they were moldings to the sloped walls so that the side surface is vertical and bottom surface horizontal. Glue securely. Now install your crown moldings as normal on properly vertical surfaces. DISCLAIMER #1 Personally, I seldom install crown moldings or wallpaper on such walls if the slope is less than 1/4 of the total wall height. I miter the vertical wall crown moldings to butt into the slant and simply paint a molding-wide stripe in matching color along the slope. DISCLAIMER #2 If you do not have access to a table saw but can measure the angle, check first with your miniature dealer to see if they will do custom light milling. Second try should be your local club If no luck there, measure the angle, draw a picture showing the angle, show the width of your chosen crown molding, determine how many total inches of sub molding you will need and contact me off the list for custom (simple) milling by mail order MEASURING INTERIOR ANGLES: If you cannot get a tool inside your dollhouse to measure angles or obscure dimensions, crush aluminum foil into the area. Remove the foil wad and measure it. Mel Koplin, Las Vegas |
Drills: I prefer the MicroLux Miniature drill in the MicroMark catalog for drilling small holes. Actually, You can use a bit up to 1/4" in this drill. But it's still a small tool. Fannye in TX |
Drills: For just drilling in thin material or in confined places I use a finger operated drill. I do not know the name of it. It is about 4"long and has a metal chuck at one end and the other end accepts the palm of your hand on a rotating ( ala lazy Susan) cap. I use old worn out Dental bits for the drilling The chuck closes fine enough to accept the bit shanks. The rotation of the bit is provided by the thumb and index finger while the palm exerts pressure. The other hand can act as a guide/stabilizer if needed. The item cost under $10.00 and can be found in well stocked hand tool sections. The Dental bits can be obtained for nothing by asking you painless;-> Dentist for them. Dr. Bob, Delray Beach, FL |
Space Challenge: Trying to "reduce" their passion for all things small to one box, or shelf, or compartment. We who are to follow are eager to see how you create. It's amazing just how much you are able to fit into one of these RV's! So far I've been able to salvage a good size cabinet in the bedroom, one drawer under the bed and my nightstand drawer, for all my crafting supplies and projects. Since I mainly make porcelain dolls, which I haven't brought with me this time, I'm concentrating on making clothing. I've further defined the type of clothing by concentrating on making only wedding dresses. This has allowed me to minimize my fabrics which I was able to get into one clear plastic shoe box. I also chose various trims and beads and stored them in small plastic bags. I picked two favorite patterns that may easily be interchanged to make yet other designs. In my toolbox, I've stored my threads, pins, small clothespins for clamps, a "helping hand" with a magnifier, scissors (several types), hemostats, several types of tweezers, tacky glue, fray check, rose making tool, small glue bottle, extra sewing needles (betweens size 12 or 15). I've found that it's been very useful to work on a small plastic tray which has about a 1-1/2" ridge all around the rim. I placed a square of dark felt in the bottom of the tray to keep needles, pins, and beads from flying all over the place. As a work area, I use the kitchen table with my tray, tool box and a foam placemat, this seems to work well for gluing, cutting, as well as assembly. I'm learning as I go so I will keep you all posted as to any new discoveries on storage or working in confined spaces that I run across. Meanwhile, if you have any that you have found work, please pass them along! Marilyn, wintering in AZ |
Drills: A small drill that is easy to use for very small holes is a "pin vise". Micro-Mark has one on sale in the March, 2001 issue of Dollhouse Miniatures in the middle of page 77. You just twist it between your fingers and it drills a very nice hole without jumping around and splintering, and you can control the depth of the hole if you didn't want to go all the way through the piece. I use it to drill holes for wooden door knobs on some of my cabinets. Spencer in Taos, NM |
Drills: I also find the Dremel Moto Tool difficult to use for the tiny drills. MicroMark has a small hand drill with a spiral shaft. You move a collar up and down to spin the drill. Of course the best way is to use a SMALL drill press, but unless you are drilling a lot of holes, probably not a practical solution. Dean Jenson |
| Previous 10 | Next 10 Page 533 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |