PRECISION DRILLING: With all the talk about pin vises for drilling small holes, I thought I would add a trick that we use to precisely position holes. The K&S brass tubing and brass squares sold at most hobby shops can be used to precisely guide drill bits. All this works because each size slips (telescopes) smoothly into the next larger size. For example, suppose you want to cut a toothpick in half and then drill a 1/32" hole precisely in the middle of the end. This may be to fit a tiny wire "peg" to strengthen an otherwise fragile joint. Find the nearest size of brass tube that will just slip over your drill bit. Use a razor saw or tubing cutter to cut a 1/2" piece of this tubing. Now find the size tubing that just fits over your tooth pick. Cut a 1" long piece of this. Now cut 1/2" pieces of each tubing size between. Slip all together with the largest over the end of the toothpick and the shorter ones butted up to it. If the largest is loose on the toothpick, wrap neatly with aluminum foil to "shim up" the space until it is not "sloppy" Drill. through the smallest tube into the wood. Your hole will be very nicely centered and square to the material. That demonstrates the basic idea. For drilling holes in edges, rather than ends, solder or super glue bits of flat brass stock as "tabs" to opposite sides of a square tube which is the same size (outside) as the piece you will be drilling at the place you will be drilling. NOTE: Round tubes DO telescope nicely into square tubes. For repeated or production drilling, you may choose to add a 90 degree guide from one side to assure your drilling is straight in as well as centered. Add a butt stop or temporary clamp for repeat positioning. For multi-hole drilling that will be repeated, build a fixture with multiple drilling tubes and work piece positioning guides. As an example, we used to make kits for wicker furniture. The seats were cut from 1/16"cherry wood with holes drilled near the edges where floral wire was inserted (plus legs and spindles at corners). We very carefully laid out the drilling pattern on a piece of flat brass. Each drilling spot was precisely marked, spotted with a center punch, and then drilled on a drill press to 5/32" diameter . We then soldered 1 1/4" pieces of 5/32" tube into each hole (1/8" inside diameter). On the other side of the flat plate, mount bits of flat stock to position the precut wood. For drill bits, we used a wire-tiny size with a 1/8" shank except at corner positions which were drilled slightly larger for legs and spindles. On the same piece of brass, we made drilling fixtures for chair and settee seats and arms plus "soldered in place" end add drilling guides for the legs, spindles, and stretchers. (Just to keep the entire set together). We spent a couple days building the fixture but could then prefabricate about 4 dozen kits in a few hours. DIY miniaturists may find production fixtures worth the effort for railings, cabinetry, and such. The whole idea of drilling guides using K&S brass goes well beyond these basics. It is a good idea to build a tool organizer block with places to keep full sets of drill bits (regular bits in 1/32" increments plus a full set of smaller bits with 1/8" shanks. Add places for each size of tube (square and round) in 1/2, 3/4, and 1" lengths plus 1" square tubes with extension tabs for edge or side drilling. I use a wood block in a plastic cube box that I can cover to take to workshops or club meetings but which gives easy access with the top removed. For those who may recall when we used to sell them, "No", we no longer make the drilling guide package. It would, however, be an excellent club project to share the costs of all those sizes of 12" long tubes. For most miniature purposes, you probably only need up to 1/4". Mel Koplin |
Sanding: I want to spread the word about Permagrit. I'm not affiliated to the company in any way, I just love the products. I had 12 internal doors to sand, and someone lent me a Permagrit block and said "Try this." I got them done in 15 minutes and the block was as good as new. No more scraps of sandpaper, no more stopping to change the paper on the block. I love it, and I'm a convert. I've got to give this one back so I've ordered their catalogue. The plastic had better watch out! Lynne Connolly |
Wind Chimes: You are trying to make wind chimes! So am I.So far, I used jewelry findings that are cup shaped, and had 'holes' in them. I tied a really fine nylon thread to the cup through the 'hole' and to this I strung a long thin silver bead. It looks like a metal pipe you may find on a wind chime. I glued the end of it so it wouldn't come off the thread, because it didn't look good if I tied it, and it took too many knots to knot the end. I tied a longer thread with a silver sequin on it for the 'donger'. But, I am going to undo the chime threads and glue them on to the cup rather than tie them, because they hung stiff, and I think maybe if they were glued, they would hang better. There are different shaped jewelry findings so you can make different chimes. Diana in New Zealand |
Jars: Try cutting plastic dowel rods and adding a finding for a cap. Looks great, easy and cheap. LadyBug |
Finding out how to reduce to 1/12th scale: The best all around method is to lay a 12" ruler diagonally on the copier. Pick a small number Like 25% and make a copy. Then lay the copy on the copier window and make another copy at maybe 33%. If you have reached 1/12 scale, the ruler will now measure 1" long on your copy. If it is shorter than this, use larger numbers. If it is larger than this, use smaller numbers, or make another generation copy at an appropriate guess. This will probably take a few tries, but it is absolutely accurate. Incidentally, if your copier has a very large reduction capability, the actual reduction number you are looking for is 8.33% Tom Berkner |
Wind Chimes: How about using long thin silver or gold colored beads for your wind chimes? (Is that what they call bugle beads?) You could attach them by various lengths of thread to a round jewelry finding. Dani in Bradshaw, MD |
Nursery Rhymes...Here are some really neat sites to immerse yourself in nostalgia. Plus a bit of adult touch to keep us alert. Have fun! I am. - Mother Goose with explanation and history. http://www.geocities.com/Athens/Forum/3041/#rhymes - A bit Modern - The Mother Goose Pages http://www-personal.umich.edu/~pfa/dreamhouse/nursery/rhymes.html - Searchable Mother Goose: Also has Quotations, American History, Shakespeare and Holy Books. Extraordinary - well worth bookmarking! Judie - Daytona Beach, FL |
Removing Quik Grab: I have also found a wonderful new product! This stuff really works! It is called Premium stripper by Klean strip. It is in an aerosol can- and has no fumes. When I popped the shingles off the roof, the residue disappeared in less than 5 minutes. We are talking down to the bare wood AND we are talking the dreaded Quik Grab glue here. I sprayed it on the beautiful fan tail design, it took the varnish off in nothing flat. This will be a piece of cake as long as I remember to wear gloves. Renee |
On this page you will find all the printable site links, sorted into categories. http://members.tripod.com/~Kalron/toprint.htm Karolyn |
Tin punch in minis: To make tin punch in miniature art form, try using aluminum foil, or a cut out from a pie plate. Use a straight pin or needle to make your punches. This allows it to be in mini scale, and not look like you reduced the size of the project but not the holes. Lisa Lynn |
| Previous 10 | Next 10 Page 534 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |