Carpeting: For an unusual carpet, keep a lookout for fabric placemats which you can cut to size, especially the woven ones. A few pieces of two-sided carpet tape in strategic places will hold it in place. Even a plastic placemat would look good on the kitchen floor if the colour was right. I have even used heavy-weight wallpaper, especially the ones with a "fabric" finish -- check your local decorating store for out dated pattern books. Also some upholstery shops have throw-away bins which you can dig through and find treasures if you just ask nicely.

Ann Kozlik


Bordellos: I had a chance to go through a famous San Francisco (really Sausalito but who's quibbling) bordello about 25 years ago. I think it had been turned into restaurant but can't remember for sure - the decor took my breath away. It was supposed to have been restored to its original glory. I think her name was Sally (Stanford?) This was one wealthy woman and her clients were among the most elite in the Bay Area. If I've gotten the name wrong please correct - - and the old cliche of all red was right there,complete with palms and silk upholstery, fine furniture, tall ceilings (they seemed to be 15 ft. high), etc.I just saw Murder Rooms on PBS and there are bordellos here with nothing but a bed and hardly any covers so the contrast can be quite drastic. Jana Joseph did a set of 4 ladies of the night (old West style) along with the Marshall and Gina Bellous ladies which have molded corsets fit right in here too. Anyone know of any others that would work?

Ana


Warping and Sealing: The only way to prevent the wood from warping is to seal it with a wood sealer product on both sides of the wood. How do you correct the wood that has already warped? If someone has a method to do this successfully, then they have very valuable information!  It's almost impossible.  Some methods to try and accomplish this is taking a spritzer bottle (like what you use to spray plants) of water and dampening it, then laying really flat objects on top until it dries (like that set of encyclopedias or your giant atlas!). Sometimes it works, a bit, and  sometimes it doesn't if the warping is really serious. I try to avoid using shellacs for primers because the clean up is a pest and they just smell so much.  Jo Sonja's Wood Sealer is an acrylic-based sealer, dries fast, and cleans up with water.  I've used this for sealing dollhouses and I've never had a problem.  Do one side of the wood, lay it on a sheet of wax paper, then about 15 minutes later, get the other side done.  If after the first side is done and you're about ready to do the second side, and it seems like your piece has raised to a curved bevel, once you do the second side, it will flatten right out.  A tip I figured out last spring...we live in a very damp area and the need for a dehumidifier in our basement is really necessary.  Last year when sealing or painting any of the dollhouse pieces, I started to lay them all down in front of the dehumidifier on the floor, then turn the dehumidifier on low and let them dry in front of that for 5 minutes.  Amazing!  They not only dried faster, but the humidity from the paint (acrylic paints) was absorbed and this too reduced the chances of warping.  I also did this with the entire dollhouse after I wallpapered each room.  I just plopped the entire dollhouse in front of the dehumidifier for 5 minutes...just sucked out all that humidity in less than 5 minutes.  Now, for those of you that don't know, dehumidifiers are expensive, but if you have one, definitely use it cause it makes such a difference. As far as the pieces that have already warped, the only choice you may have is to replace them.  If it is a tab and slot kit (most likely one from Greenleaf or Corona), it's Luan wood and you can buy this wood at most wood supply departments ..home depot, etc.  It's splinters easily and it's nasty to cut, but this will replace your spoiled wood pieces.  Draw the outline of the piece of warped wood on the new wood (be sure to hold it down flat) then cut it out.  If you have a scroll saw or know someone that does, this will help because the blade cuts fine and there will be much less chance of splintering the wood.  Go slow, take your time and it will work well.

Joy in Pointe Claire


Warping: For warped wood, I soak the piece in the bathtub then place it on the garage floor, cover with wax paper and drive the car up on it.  If it is really large, cover it with another piece of wood before the car tire.  Leave it overnight.  It does too work!!!

Fannye in TX


Bordellos: I haven't heard any of the Texans speak up for the "Chicken Ranch." This was the true life model for the movie with Dolly Parton and Burt Reynolds, "The Best Little Whorehouse in Texas." I've wanted to build it many times, but it's just not been on the top of my list

Fannye in TX


Cutting Luan: If you score the Luan on the "cut" line with sharp utility or X-Acto knife, using a straight edge, you will minimize to problem of splintering. This works well on any plywood also.  When cutting on a table saw, place the "good" side up so the blade won't tear out the wood on that side.  If your using a hand circular saw, place the "good" side down.  You can also use some masking tape on the cut line to eliminate tear out.  These tips also work with full size lumber for "real life" projects.

Spencer in Taos, NM


Warping and Sealing: I presume from the warped wood problem you have that you are doing a house with 1/8" luan. The problem is often in the manufacture of the plywood (they didn't use equally dried wood )and not with the kit mfg. I have found that many times one can pull the warped piece into alignment when the house is fastened together if the warp is not too bad, but o straighten a warped piece I use this method: DO NOT  seal the wood first! Place the wood with the warp (the curve facing to the floor), then SPONGE the convex side with preferably hot water (do not wet both sides of the wood). You will need to get that side fairly wet and spritzing it does not get enough water in and on to do any good. Then flatten it out and lay REALLY heavy weights on it. Then let it dry thoroughly.  BE SURE TO KEEP THE CONCAVE SIDE DOWN AND THE CONVEX SIDE UP like this ^.  You will have a 50-50 chance of getting it to straighten out. You can then seal both sides AFTER that. As to the shellac: I think many of the  manufacturers are calling it a primer (I can't think of too many other uses for shellac).  The one I prefer with the dollhouses is white shellac - it has a white pigment added. This will give you three benefits even thinned: 1. you can see exactly where you have painted (clear shellac dries very fast and is almost invisible when dry) 2.it primes the walls inside so that your wallpaper's color remains clean and the glues are not sucked up into the wood. And 3.by priming BOTH sides you now have solved any future warping problems. Clear shellac is also good but stay clear of orange shellac because of the color problem. Shellac does not have to be used straight (as it dries out over the years it tends to "alligator"- remember all those crackled finishes on antique furniture?)  - its effectiveness for the purpose of sealing is perfect at the proportions of 1 part shellac to 5 parts DENATURED alcohol (obtainable where you get the shellac). The Furniture Guys of Furniture To Go fame call it a spit coat.  As an aside : for anyone who has an animal odor problem (your dog pee'd on the floor and you can't get the smell out or mice made a home in your piano or whatever) or you have a color paint problem like trying to cover red with white (red always bleeds through) use shellac...it creates a barrier to the offending odor or color).  I found this hard to believe but that spit coat DOES do the JOB!

Ana Gerard


Gesso: The best gesso on the market, in my opinion, is Liquitex brand. I bought mine at an art/arts & crafts store.  The bottle I have is several years old, it is a 1/2 gallon (54ounces) and can be used for canvas or whatever you need it for.  I think it has thickened over the years, which makes it better, and maybe you could thicken it faster by leaving it without the lid. It will skim over, but it is still good.  That large bottle will last a very long time, but I use it for many things.  I used mine last week to seal wood and siding on the outside of a room box.  It is white in color, acrylic, no odor and water clean up.  Of course, you can't use it if you are staining. For that I would use a "spit" coat of shellac (1 part shellac and 5 parts denatured alcohol).  It helps even out the stain, and is good for sealing dollhouse kits before assembly.

Patty Adamson in Bandera TX


One of a Kind Wallpaper: I made my own wallpaper. I took a digital photograph so I could get it into my computer. I used a photograph of a plate from a magazine. You could use a pattern from fabric and scan it...the idea is to get it into a graphics program on your computer so that you can change the colors or take out the round, plate shape, take out a shadow whatever has to be done to it. Then you copy, paste the best part into a program where you can save it. duplicate the pattern onto the page as many times as you need then print. You aren't done yet. As soon as it gets wet, your ink will run, so you need to spray it lightly with an artist fixative for use with ink. DO THIS OUTSIDE. Most of these things are not compatible with life.  Spray both sides and let it stay outside to air. THEN, you are ready to use it as wallpaper and its exactly what you wanted!

Laurie Sisson


Ceilings: Someone asked about creative things to do with ceilings. I use a lot of moldings and wall decorations from Architectural Etc. to give some interest to the ceilings.  Something else to try  is using the  paneled wallpaper that is made by Mini Graphics.  Cut out the panels and you can put them on the ceiling.  I think you can see what I've done with ceilings at http://www.spminiatures.com/house where I have pictures of my dollhouses.

Carol


Previous 10 | Next 10


Page 553 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)