Stone: Have you considered using "Magic Stone" on your house? You paint the house the color you want the grouting to be (some shade of gray, usually) and when the paint is dry, you put on a sort of tape with stone-shaped holes in it, and smear a gritty paste all over it. Wait a few minutes, then pull off the tape, and there are your stones. You can dab at them with different shades of paint for a more realistic look, and then spray it with a matte sealer. I used it on the foundation of a house I finished for one of my grandchildren. Six or seven years of "hard labor" and it still looks good.

Another possibility is Precision Products 3-D plastic sheets. They have slate, cinder block, stone, etc. The sheets are 15 inches square and can be cut with regular scissors or a craft knife. The address is 763 Cayuga, Lewiston, NY 14092-1724. I used the slate on the roof on my Fairfield, and was quite pleased with it.

Dani, in Bradshaw, MD


Stones: A few of us on the MiniProjects list use packing peanuts to simulate stone. I also found a great product called "Pumice-stone Mortar" by Pebeo. It's made to be used by artists with acrylic paints and when used by itself looks a bit like granite. It would be good for painting stonework or sidewalks. You could paint it on, scratch outlines of your stones and then fill in the "grout" or "mortar" later.

I've found that the mediums sold in art stores are a great resource. There are all sorts of cool stuff like the pumice one and stucco and sand to name a few. They are a nice fine texture and can be mixed right with your paint. Cheap too!

Melani


Coloring Stain: Big hardware stores ought to carry a variety of colored stains. If yours are like mine and don't, here's what I did:

I started with Behr brand Eurocolor water based wood stain in "Monaco White." I put some of the stain in a jar and added Plaid brand Decorator Glaze (something I bought at Wal-Mart to use when stenciling designs onto my floorboard radiators) - if I were going to do it over I'd probably just use plain old acrylic paint. The main reason I used the glaze is that it was "there." Stir frequently when using to be sure the pigment stays evenly mixed. Just be sure when you mix colors with stain that you use a water-based paint with a water-based stain and oil-based paint with oil-based stain. Mix small amounts of colors in until you have what you want. You might want to do a test painting to see what the actual dried color will be. It's also interesting to experiment with the length of time to leave stains on the wood before wiping off. On my floors, I didn't wipe off the light colors at all, wanting the most color saturation I could get. When I went over the dried light color with a darker color, I immediately wiped off the dark stain with wet paper towels (don't wipe too hard or too long in one place, or the light stain will come up, even if dry!) Since I hadn't sanded the plywood of the floors too well - on purpose! - lots of little tiny indentations in the wood caught my dark stain, while the surface of the wood stayed lighter in color. Of course it is essential to seal the stain with the appropriate sealer.

Frances


Wood stain - I have a limited amount of storage space, and therefore don't want to be bothered with finding places to keep numerous bottles and jars of paints and stains. So, I make my own stain. It's really easy. I buy the type of water-based glaze now popular in faux finishing and mix it with whatever color acrylic paint (usually craft paint) I want to stain the piece. The glaze has a milky white look in the can, but dries completely clear, and will not effect the color of your paint. To apply, I use a small paint brush, and put it on in very thin layers until I achieve the depth of color that I want.

I also like this method better than regular stain because there is no need to apply it, then wipe it off. And, I only make as much as I need. Another benefit is that it adds a great depth to the colors. It comes in satin, semi-gloss, and glossy finish, so you can control the amount of shine you end up with. But, be aware that the acrylic paint will "flatten" the finish somewhat.

Sloania


Staining furniture after being glued together: I think that it's quite impossible to remove or clean the glue from the wood, because the glue is now inside the grain of the wood. I suggest now to paint the furniture with acrylic paint (you can use burnt umber mixed with a little bit of crimson) diluted with water (normally 50/50). Before painting your assembled kits, try your paint solution to a piece of scrap wood.

Paint your furniture and allow it to dry, then sand using steel wool (extra fine 0000) and apply two or three more coats. After that, paint grain lines using a thicker solution of paint using an old brush with trimmed bristles. You must work in only one direction, trying to copy the natural grain of the wood. At the end polish your furniture with dark-wax polish for wood. Allow to dry and then buff the piece with a soft wool cloth.

Pierluigi - Italy


Stains and Glue: If you seal the wood before you stain it, the stain can't sink into the wood. I have always applied an oil based stain, wiped it to the color I want, then I use my finish on it. As for glue, Elmer's Wood glue is better than white glue - it has a yellow color and is stronger and doesn't break down when it gets damp. There are probably other glues equal or better. For full size furniture I used Hide glue (actually made from animal hide).

Jacqui in Hilo, HI


Gold Leafing: I just finished some leafing (an illuminated letter), so I can answer a few of your questions. You will need the glue called "gold leaf adhesive size", which should be available at an art and craft store where they sell leafing in packages. The one I bought is a water-clean-up (my favorite!) from Houston Art, Inc. I looked for their web site, and found them at  http://www.houstonart.com Click on "gold leaf". They have a book for sale on their site, but all the instructions you need are on the bottle. I have only done paper projects, though, so maybe someone else can fill in on how to prep furniture (I know that you need to paint it with a color first). Interestingly enough, I was playing around with it (and also saw on Carol Duvall's Show) and found that it will stick to a design made with a hot glue gun or Aleene's 3-D Foiling Glue, which gives you all sort of creative possibilities. The variegated foil they mention on the site is my favorite (at least for the illuminated letters I have done), although in the years since I bought my first package, the price has gone through the roof. I think the patterns are too big for miniature work, though, but it sure is fascinating stuff.

Marilyn, Wisconsin


Colored Pencils/crayons:  you can make color crayons and color pencils with the thin colored wires in phone cable. Just cut to size and "strip back for the "lead". Paint the little copper end in a color for crayons and lead color for pencils.

Anita


Tin ceilings: Some chocolate bars come wrapped in an embossed foil that looks like miniature tin ceiling. Also in shops that cater to cake decorators you can buy many designs of embossed foil for covering cake boards. (And you'd be surprised at all the other possibilities for miniaturists too.)

Elli in NZ


Wine Keg: I'm not sure if I remember correctly if a wine keg looks different than a whiskey barrel, but in Lee Valley Tools' main catalogue, they have whiskey barrels. Tuned on their side with a spigot, they would look quite realistic. They are solid and stain/age very well...and like a number of wooden pieces they sell, are perfect for 1/12 scale. You can request their catalogues from their website: http://www.leevalley.com

Joy in Pointe Claire


Previous 10 | Next 10


Page 595 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)