Sand paint: I use a sand paint on my Southwest roomboxes. I make it from a very fine grain sand that I get from a hillside here in Taos, NM. I add it to a very good quality wate- based paint and stir it in well. I test the "look" of the paint by brushing some on a piece of scrap in a circular motion and continue adding sand as needed. The paint should be stirred every so often to keep the sand in suspension. I sell this paint in 1/2-pint cans in a Navajo White and Desert Sand. Two coats usually do the job. Normal beach sand is usually too course to look "in scale" for miniatures, so I would suggest getting some mortar sand from a concrete company near you, if possible. I think that if you smear the outside with glue and then spread sand on it, the paint might not stick on the dried glue. Spencer Stall |
Shingling Angles: Don't know if you all are aware of this but we do something when we weave a valley when shingling a gable, etc. We cut a group of shingles diagonally, works best with rectangular as you can use both sides, and start from the inside. It makes the weave line up perfect and you can judge when you get close to the end whether you need to adjust a shingle or two towards the edge of the roof. We find this saves quite a bit of time. Hope someone finds this helpful, I know we like to do it this way. Rick & Bonnie |
Shingles: Water-based products and dollhouse shingles don't mix. To apply shingles, use a glue like QuickGrab. To stain shingles, use an oil-based stain. Fun tip: get a large freezer bag, pour in a couple of ounces of stain, toss in handfuls of shingles, zip-lock the top of the bag and shake until the shingles are evenly coated. Sprinkle the shingles out of the bag onto several thicknesses of newsprint and let dry. Sally Cook-Thomas |
Shingles: How To's/Hints: Cutting and staining: Some years ago I found a pair of hand-held shrubbery shears at my Home Depot, for about $5.95. They are the tool I have used to cut shingles. Mark your shingle with a dark pencil line, and use a quick or fast cutting motion. Once you have got the first perfect one, mark it as your pattern, on both sides so you don't glue it on the roof by mistake (can you tell I have done that before?) I use any stain from the local home improvement store or hardware store to stain shingles. How to stain shingles: Start with an empty plastic gallon milk jug. Cut off the top portion with the handle. Poor in all of your stain. Now put in a handful of shingles and stir, remove and lay out on newspaper to dry. The drying takes about 24 to 48 hours, and then you are ready to start your shingle installation. You can also dunk a few shingles in the stain can prior, and let them set in the stain for 15 to 20 seconds to test the color. I do this 4 to 5 times, with different lengths of time. The longer they are in the stain, the darker the shingle will become. Be sure to write down the time you used in your test, let the shingle dry and choose the color you prefer. Andy |
Dying shingles: The best method to dye shingles depends on the effect you are looking for. If you just want colored (or darkened) shingles, then dying them in a container (plastic bag, milk jug, etc) is the best way to go. If you are trying to make an 'aged' roof, then you need to dye them after they are on the roof. For an aged look, use subtle variations in shade, and you need streaks. Streaks must go for several rows, not just one shingle, and color variations are over areas, not each shingle, which is the reason for doing it on the roof. Things that cause the variations and streaks are chimneys, vent pipes, TV antennas (don't see many on dollhouses), exposed nails, areas that are under the overhanging trees, different exposures (north vs. south), valley and hips, little piles of debris caught in the valley. I don't like the oil-based stains, because they are messy, hard to clean up after, and slow drying. The water-based stains solve these problems, but often cause the thin wood to warp. Alcohol-based stains/dyes overcome all these problems (water clean-up only). If you obtain a dye that is not premixed, you can start out with a lighter color, covering the entire roof, then add more pigment, and overcoat some areas, add more pigment and repeat. You can add still more pigment and brush on streaks as appropriate (or as you like). Tom Berkner |
Applying and staining shingles: On my log house, I glued the wood shingles down with carpenters glue. After it dried for a few days decided to stain them as the color matched the logs too closely. At Michaels I purchased a color stain in regency red made by "Anitas." I used a small 1/2" brush and carefully started at top of ridge of the roof. Had no problem with runs and love how it turned out. Doing it this way the shingles didn't warp from wetness as they were tightly glued down. Alice Prosky |
Lattice: plastic needlepoint canvas can be used for lattice. Get it in white and cut diagonally to get the criss-cross design. I have also seen it 'straight up and down' on older houses. Martha Simpson Nock |
Halloween scene ideas: My almost-five year old granddaughter and I are making a little witch's party scene, using the wire furniture from MacFrugal's. So far, we've put a tablecloth (tiny square of Halloween fabric) on the little round table and made and/or glued these items on top: Snake eggs with spider sauce (marble-like contents of little dessicant bag to keep moisture out of things, with a drop of amber Gallery Glass on top), Pigs' tails (white cloth-covered florist wire painted pink; wind around toothpick, slip coil off and cut into tiny snips) Frogs' legs (tiny green plastic stems and stamens for Queen-Anne's lace-type flower bloom) Dragon's eyeballs (tiny polished rocks with pupils painted on) Halloween candy made from canes (I cut these) Cookie made from painted lentil Witches medley (tiny seed pod painted like pumpkin; dried pods and bean, tiny foam balls in fall colors Roasted spider (look at dried heather; see the stamens and little leaflets; paint those black and snip off Boo cakes (string together alphabet beads spelling boo) Flies (half a clear plastic pill capsule coated with glue and poppy seed sprinkled in; glued like a dome to paper punchout) Candle (half a toothpick painted orange, stuck in a slightly flattened black bead) Containers were a round platter made from a slightly cupped white plastic disc with a hole in the center (no idea what it was originally intended for), the center of which was covered by a tiny Halloween ornament; snake eggs bowl made from a plastic pill container painted orange inside; a small heart charm; and a fruit bowl cut from a candy mold. The cost for this party table was the cost of the table (99 cents); everything else came out of my stash of stuff. We're also planning to make a new black dress and hat for the little kitchen magnet witch (which I got for 90% off after Halloween last year). She needs new hands because I had to cut one wire arm apart to get the magnet off, and feet, too, because they're just felt blobs. My youngest grandsons, aged 8 and 6, are going to make a scene, too. So far, they've made witches' hats. I think they want to do something other than a party table. Maybe a boiling cauldron with something gross in it. Wanna in El Paso |
Halloween Spiders: You can make spiders with 4 pieces of wire wrapped with thread in the middle in a spider shape. We used to make them with old fashioned hairpins when I was a kid (seems not so long ago!) Glue the thread with white glue and hang from a thin fishing line or black thread. Hot glue makes great spiderwebs (only when I don't want webs!) Rhoda Conley |
Southwestern site for Indian Designs is: http://www.zianet.com/mikemosier/ Parisa Javidi |
| Previous 10 | Next 10 Page 644 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |