Plank floors: Why not use edge banding for plank floors. I have done two floors with this and they look super. It irons on and is real strip wood. The real use for this is the edges of counter tops. Three quarters of an inch wide, fifty feet long for twelve dollars. Doris of Ottawa, Canada |
CUTTING DOORWAYS IN ASSEMBLED ROOMS: We tend to think of saws as tools that must first penetrate the wood at one end of a line and then cut along that line.Unfortunately, once a room is assembled, there may not be room for some tools to fit and even when they do, we may start, only to have saw handles hit floors, walls, or other ceilings before the cut is finished. It is time to think outside the box. . . X-acto and Zona offer "razor saws" in several sizes. (I far prefer Zona.) For those not familiar, a razor saw has teeth along one very straight edge of a rectangular blade. The opposite edge of the rectangle has a metal stiffener which culminates in either a fixed handle or a tang that can be fitted into a removable handle. It looks much like an old fashioned straight razor - hence the name. As you move the teeth along a line to be cut, the handle/stiffener is well above the cutting surface. This clearance is variable depending upon the particular razor saw. Some have a minimal (1/4") clearance. Others in my collection offer up to a 2" clearance. Cutting out to enlarge an interior doorway, mark a line. Cut off or leave off the handle of your razor saw, grip it along the stiffener and guide it back and forth along the entire length of your line. This is easiest if you temporarily tack or brace a piece of scrap wood on the line to guide your saw against. Take your time (it will go slow) and let the saw do the cutting. You will end with a clean, straight cut right down to the floor line. If the saw stiffener starts bumping into the guide wood before you are all the way through, remove the guide wood. Once started, the groove will be your guide. Your groove cut MAY go beyond where it has to be if you are going to recover the wall(s) anyhow. After all cuts are done and the unwanted wood removed, simply glue a thin piece of basswood (1/32" sanded down to fit) into the extended cuts and sandpaper flush. I have cut the handle tangs off of the blade stiffeners on a couple of saws to work in confined areas. I have also used Dremel abrasive discs to cut down a couple of old saws to smaller (shorter) sizes. A step beyond razor saws are "Japanese" saws. Check these out at a high end woodworker's specialty store or in the hardware stores of Asian ethnic communities. These saws usually have no stiffeners but the teeth are arranged to cut in the "pull" rather than "push" direction. A specialty blade within this category has a gentle curve, so starting a cut involves only a few teeth. As the cut progressively goes deeper and the groove becomes established, more and more of the saw teeth are used. One more tidbit. When I can get it into place, I far prefer routing rather than sawing. Using straightedge guides I get neater, more precise cuts with a router. Doing a doorway I can not get down to the floor but usually can do the horizontal cut of a doorway plus beginning the vertical cuts which then may be finished with a Japanese saw. Mel Koplin, Las Vegas, NV |
Castle stairs and stairails: I think that the "rope" idea is good. If you used wood, you would have to score it to facilitate the curve, then soak it in water, bend the curve and clamp it and let it dry. With the "rope," you could glue jump rings (they come in silver and gold tones - I think that I would paint them black) to the wall, run the "rope" through it with a knot tied at the top and bottom. You could even add another one on the outside edge of the stairs by using T pins. I would cut a small piece of plastic tubing (IV or oxygen tubing - I can get you plenty of this if you want to try this) to cover the head of the T, cut the pin down to the height that you need and paint the whole thing black. Then you glue them to the outside of the stairway and run the "rope" through as with the other side, with a knot tied at each end of the "rope." For the stairs, if you wanted to use foam, couldn't you use a sheet of foam the thickness that you want your steps to be wide, cut a square the size of the height of a room (you could make it a rectangle if need be), then cut out the stairs? When you cut it apart, you should then have 2 sets of stairs. You could then paint them gray and "carve" stones in the side that will be facing the room. You could even cut out indentions in the steps for a "worn" look. Glue it to the wall of the tower and attach the handrails. Rusty |
Flower Punches: You can find flower punches onhttp://www.etropolis.com/mini/hooked/index.htm Deb |
Flower Punches: To order paper punches:http://www.punchpalace.com/mini_extension.htm Marjon de Haas |
Flower Punches: Control Concepts, Inc. (formerly P.J.Mieth), P.O.Box 205, North Branford, CT 06471-0205, phone 203-457-0557 for your punches. They should have a catalog showing you all the different punches. Sir David |
Color Problems: If you're uncertain about colors, try the faux room at http://www.fauxlikeapro.com/smd.html Jean Berry |
Guild School: The Guild School is in Castine, Maine in June. It's held every year in the Merchant Marine Academy while the sailors are out at sea. You need to contact the Guild www.igma.org first, and see what classes you are interested in, then sign up and show up! Your housing and meals are included in the fees. If you can't get to Castine there are also "Study Programs" held in various parts of the country. Check them out on the web page. The Guild's teachers are all either Artisans or Fellows of the Guild. Yes, it is intensive - a whole week devoted to nothing but miniatures -and also lots of fun! Particularly the lobster dinners. You might consider taking classes at Tom Bishop's Chicago International Show. The list of classes is HUGE, and the teachers are excellent. Check that out at www.bishopshow.com Nicole Walton-Marble |
CIMTA Directory: For those of you wanting to locate stores during your travels, you might go to the CIMTA site http://www.cimta.org and click on the shopping guide. All supporting members of the organization are listed, many of whom have linked web sites. Not all stores belong to CIMTA, but a great many do and it is worth a try. Ann Hendricks |
Guild School: The Guild School lasts about one week, commencing on a Sunday and ending on Friday evening of the next week with graduation. All room, board, and 36 hours of instruction are covered in one fee (extra classes, airfare, sale night and classroom fees are additional.) To get the best information you can log into the IGMA website at www.igma.org. You can also email the school director for further information at badavis@cats.ucsc.edu. You can also call IGMA toll free at 1-800-711-IGMA for any and all information regarding the Guild. Sandy Wall |
| Previous 10 | Next 10 Page 650 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |