Chrysnbon kits finishing: I hated the finish of these kits but loved the detail. What was suggested was to go ahead and use the water based "stain" that came with the kit. When dry, go over with some dark HOM stain (not water based - would eat the plastic so that's why the base coat). Wipe off some before it's dry and after it's dry - buff. I found a particular clear water based top coat that I liked very much but it's name escapes me. The results are fantastic - they indeed "fool the eye" which is my goal - since I need to use my creativity instead of a limitless budget:)

W. Marie


Staining Kits: I always stain all of the wood pieces of any kit or box that I am building first because if I glue them together, some glue usually seeps out from the joint will and act as a sealer that the stain will not penetrate.

Jeanette Zanio


Wood Floors: I learned from Brooke Tucker to glue my wood floors to heavy poster board. I use Quik Grab glue and weight it until it sets up (I leave overnight). Then use a palm electric sander and sand with the grain of the wood until very smooth and go ahead and finish. I usually stain ahead of time but have done it the other way also as you have no glue problems. Then Spray (or paint) a coat of deft semi gloss and "polish" with a fine steel wool. Usually repeat the deft thing about 3 times if I use spray and twice if I brush on (lightly).

A palm sander is about $20 and a terrific investment if you like hard wood floors. Then you can just tape these floors in.

Rooms in My Collection. Though that room is not quite complete yet the floor shows well. Again, I give credit to Brooke Tucker for this tip.

Anita MH


Hardwood Floors: I make my hardwood floors out of pre-glued hardwood veneer edging - you iron it onto cardboard. It always warps but I found that if you heated it up as high as you dare and then weight it whilst it is still hot it will lay flat eventually - two or three heatings may be necessary.

I was wondering if you could take one of your existing floors, heat with an iron and then put it into the book press. It might do something to reduce the moisture content ??

Lesley


Hardwood Floors: I laid a hardwood floor in my current project and I am so proud of it. It turned out beautifully. I used oak sheet wood that I purchased from a mini store. I have a table saw (mini) so I was able to rip my own strips to the size I chose. I cut them into differing lengths and laid them out first on a template of my floor over a double-faced tape grid to hold them in place. I would probably skip this step if I do it again, but I'm glad I did it for my novice attempt since I was learning as I went.

Once I had it all trimmed and laid out to suit me I picked the pieces up and glued them down to the actual floor one by one with regular yellow wood glue. I intended to stain my floor so I was very careful with the glue. I went fairly slowly and made sure that my strips were pressed firmly up against their neighbor with some little metal weights with straight edges and perfect 90 degree corners that I use for everything! I have no idea what they are in "real life".

Once it was all glued down I sanded and sanded and sanded and rubbed the sanding dust down into the spaces where the wood pieces came together to fill in any little spaces. Then I sealed with a thin coat of polyurethane and sanded and sanded and sanded and rubbed the sanding dust down into the spaces where the wood came together to fill in and sealed again :). Kept up this drill until I had a smooth as glass finish. I read somewhere when I was studying up for this project that you should be able to close your eyes and rub your fingers over it and feel one continuous surface.

I then stained to the color I wanted and then waxed with paste wax & buffed. Between all these coats I weighted it down under heavy weights to keep it flat. My only mistake that I can see is that I didn't use a thick enough piece of wood for my sub flooring (that I glued the wood strips to) and it did warp just a bit even with the weighting. I used sub flooring just to make it easier to manage and was able to correct the warping when I glued it into the house, so no harm done---but it could have been a problem, so do try to avoid that. It turned out beautifully. It was a good bit of work, but I think the result was well worth it.

Jane, Little Rock, Arkansas


Making shingles lighter: When I paint pictures, wood and cardstock, I go from light to dark. Meaning that I take a light color and begin to make shadows with medium and dark colors of the same hue. But the same idea will work in going from dark to light, it's just more tedious. If it were me, and the shingles were on the roof, I'd dry brush the shingles using an artist fan brush, or use a sea sponge, with medium and lighter shades of brown paint. And I'd use my fingers to blend the colors, either that or bits of paper towel, blending each stroke at a time. About the watered down paint, I've used this to lighten a dark painted area, and also used it to darken a lighter section of paint, so I've used this one both ways, but both ideas work fine.

Susan in VA


Hard Wood Floors: We use Bond 484 glue. Starting at the front of your house, spread glue on about the front 3" of the floor. Cut the first strip to length and lay in down, tight against the front wall. Take the remaining piece of that strip and lay it against the first strip, starting from either side wall. Cut a piece to finish the rest of that strip. Use the remaining piece to start the next wall. Continue in same manner. When you get close to the edge of the applied glue, spread another 3". Some people like more joints in their floors and make extra cuts, instead of laying such long pieces. Make sure the joints don't line up. Once the floor is covered, fill the room with books, bricks or blocks to weight the floor down over night while the glue finishes drying. It is a good idea to lay down wax paper over wood before the bricks, so they don't get glued down if any glue squeezes up between the strips. Next day, remove books. Sand floor. Apply finish (we like Deft), 2 coats, sand with 300+ grit paper or 0000 steel wool to remove any dust specks.

Apply last coat. You'll never go back to coffee stirrers after using a nice hardwood for your floor.

Tom Berkner


Flooring: Our second method (when we do it outside of the house) is to lay it out and glue it down onto a manila file folder. Weight it down over night (or use book press if you happen to have one). Trim to size. Sand it smooth. Glue it done on dollhouse floor. THEN you can varnish, oil, paint or finish it in whatever manner suits your fancy. Do NOT apply any finish before you attach it to doll house.

Tom Berkner


Making a country mini: Here's a tip for those who paint little country items, I just painted a little country doll on cardstock. I did the dress in wine, and then when that was dry, I mixed up some watered down white paint and painted a pinafore over the dress. Went back with straight white from the bottle and outlined the pinafore and it makes the pinafore look very sheer. I made a front and back of this little doll. I cut her out and glued the front and backs together. I made a tiny round base out of cardstock and painted it. When that was dry, I stuck a straight pin up through the middle and went clean through the two pieces of the doll and she stands up just fine. So if anyone out there is doing country items, thought I'd pass this tip along.

Susan in VA


Hardwood Flooring: Lee Valley Tools carries a lot of good woods and veneers... I bought cherry veneer strips in 3 widths to do flooring with. Came in tubes, about 300 or 400 strips to a tube. Now, it is veneer after all so would need to be mounted to something else but I am confident it will make gorgeous floors some day. I am an ardent Lee Valley Tools fan! They carry tons of things that we miniaturists can use, reasonable prices, excellent quality and best of all, CANADIAN. And they will mail order you can request a catalogue at their site. http://www.leevalley.com

Bob Francis, Calgary, Alberta, Canada


Previous 10 | Next 10


Page 665 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)