Deft: Yesterday I finished a couple of Mini Mundus furniture kits. I used Min Wax wood stain but for the first time I tried Deft sealer in a spray can. I think it was "our Tom" who suggested this a while back. I had never used a spray sealer before - I think I suffer from "Fear of Spray Can". I was totally amazed by the beautiful finish I got. I applied 3 light coatings as the can said, and then rubbed the final finish with very fine steel wool. Lovely.

P.S. - Every time I buy a Chrysnbon kit the wood stain that comes with the kit has dried up, so I don't know if it is any good or not. Today I tried an experiment. I tried Gel Stain on it. This does NOT work. It went on streaky and stayed sticky. Luckily I could wash off the plastic with soap and water and start again. This is a definite - do not try this.

Paula in NJ


Fabric for Wallpaper: Saw some instructions on applying fabric as wallpaper the other day. They suggested using carpet tape. Why don't you use the sticky backed foam board you mount needlework onto? Just cut it the size you want for the walls and paper it w/o being inside your dh. Don't forget to leave an overlap on the first wall so when you put the next one on, it will show joined and not showing a crack.

Lisa


CRACKLE

I finally got the hang of the fragile crackle thanks to Andrea Barham's directions in her latest book. It's really a four-step process.

  1. Paint the color you want the cracks to show as.
  2. Paint the Step 1 crackle and let it dry.
  3. Paint the Step 2 crackle.
  4. Paint the top coat while the Step 2 crackle is still tacky. Step 4 is the crucial one; really gooping on the Step 2 crackle is also important to be sure you get plenty of cracks in the finished product.

Loretta Sniarowski


Wallpapering with Scrapbook Papers: I have used regular miniature wallpaper as well as the papers from the scrapbook stores. I use YES glue exclusively. I do NOT thin. Put the glue on the paper with a spreader, credit card or stencil brush or cut of stiff 1" brush. Put it on thin to cover completely. Slide the paper into position and smooth it out with a credit card or plastic spreader. I've never had any wrinkle, bubble or look awful.

Fannye in TX


Wallpapering with Scrapbook Papers: I used "cloud" scrapbook paper for the sky in my "Secret Garden" with no trouble. I used dollhouse wallpaper paste with no sizing (that fake wallboard). It seems to bubble after pasting, but levels itself out when dry. I used a similar paper--brick pattern bought from my pet dollhouse store on "Rachel's Stable" on an old wooden box. It did the same thing--bubbled and then smoothed out.

Betty in Bellevue, Washington State


Wallpapering with Scrapbook Papers: I successfully used scrapbook paper by applying it (over primer) with Mod-Podge.

Susan


Wallpapering with Fabrics: I have used fabric for wallpaper quite successfully. I used Mod-Podge for applying the fabric over walls primed with acrylic. It worked very well. You need to prime really well. I used rather thin fabrics.

Susan


Shingle tips: I wanted to share a shingle tip that was told to me by Roger of My Doll's House in Torrance, CA. He uses hot glue for putting on shingles, that way if one becomes broken you only need warm it up to remove and replace it (also no warping and curling like you get with some glues).

He also either cuts a 1/16 x 1/16 length of wood (or cuts shingles into slivers) and places them at the very edge of the roof, then placing the first layer of shingles on top of it. That way they all look even.

Ami


Cutting Holes in a Shell: I can't think of any good, neat way to cut a rectangular hole in the 3/8" plywood exterior roof of a house for a dormer.

If you are brave, you can use a laminate trimmer with a straight bit. This is one way the pros cut out dry wall in full scale. A little scary, however.

If I had to do this, I would use a little circular saw you can mount on the same mandrel that is used with the cutoff wheels on a Dremel. I would use a flexible shaft on the Dremel and a slow speed and carefully follow the line. Cut no more then 1/16" deep per pass. This should work if you can find a 3/4" to 1" saw blade, the finer the better. (Let me know if you can't.) I believe a company called Gyro makes them. And, if you try this, be sure to feed against the rotation of the saw and be very careful and feed very slowly. The blade can kick back and do damage to the house and your fingers. You can hold any angle you need.

You probably don't even need the flex shaft but that allows more clearance and better control.

Pete Boorum


Hot Glue for Dollhouse Shingles: If you do decide to use hot glue always use the hot melt, never low melt. And even then be very careful. A friend of mine consistently made crafts using low melt hot glue and when we did shows her glue melted and her products fell apart. You may not foresee a time when you will live in a place this hot or your house ends up in a hot attic, but you never know.

Laura in Tucson


Previous 10 | Next 10


Page 666 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)