Wallpapering Preparation: The necessary preparation for wallpapering depends on the substrate. If you have a porous plywood, (like luan - Greenleaf, Real Good Toys, Walmer, etc) you should seal the wall in some way before wallpapering. I find that shellac diluted 5 to 1 with alcohol does a great job of sealing, and dries very fast (5 minutes or so). For wallpaper paste, do not use anything containing a fungicide (mildewcide). Some of these will react with the copper in the wiring and create cupric oxide (a black corrosion) which doesn't have any great effect on the wire, but the black will show through many papers. Life is also easier, if you use a paste that will NOT cause the paper to stretch (cause then it shrinks when it dries). For these reasons, we use YES paste. Some people advise mixing water with the YES paste so it spreads more easily. DON'T DO IT. You have just defeated the nonstretch of the paste. The paste can be very easily and evenly spread using an old credit card. You want only enough paste left on the paper to make it look shiny. If your house is built of a fine grained, reasonably dense plywood (such as birch), I have found no necessity of sealing the walls before papering (this is 25 years of experience). I have never papered over MDF, but I expect it would be good to seal it first. Some more tips? Assemble the house and then paper. Paper before you install, windows, door, baseboard, etc. Paper the ceilings first. If you aren't going to install crown moulding, paint the top of the walls and the edge of the ceiling the same color as the ceiling paper. Cut the paper to 1/8" shorter than the height of the wall. Always cut the bottom edge of the paper, because any unevenness will be hidden by the baseboard. Paper the front wall of the room first, bring the wallpaper around the corners onto both side walls. Then paper the side walls. This way, any shadow line from the overlap is not visible from the back. Butt the factory cut edge of the paper against the ceiling. A credit card (or one of those thingies - tech term - from the auto parts store that is used to spread body putty) works well to smooth the paper on the wall. After glue has dried, cut out window and door holes using craft knife - be careful to NOT cut any wiring. Tom Berkner |
Pre-pasted Wallpaper works GREAT! Better than the real stuff. It's easier to fit too and slides better. I think gluing pre-pasted is a wasted step. I have used it in several rooms on pre-painted walls, and had no problem with it. SA Burr |
I am building a Colonial Williamsburg (VA) type house. I used the wood punched out from the windows to make raised panels on the lower part of the dining room walls. I tapered the edges with a Dremel using the sanding bands, then glued them to the wall evenly spaced. Painted it all the same color, along with a chair rail. Then I put a scenic wallpaper above the chair rail. Martha Simpson Nock |
Wallpapering: To prepare wood for wallpapering - you have two choices I know of. You can use regular sizing like you would in your "real" house - and that is the cheapest way - you mix what you need and can save any leftovers in the refrigerator for quite a while. The other choice is to paint the wall with household latex paint. Both will act as a sealer which is what is needed. Jeanette |
Do all your painting (ceilings, outside, etc.) before you wallpaper. Jonesy |
Painting Clapboards: I painted the siding before putting it on the house, using a latex spray paint from the hardware store. Sprayed about 4-5 thin layers, sanding in between each layer until I had the desired coverage that I wanted... looked great when done. That was 3 years ago and it still looks great. Be sure not to overlap your spraying on each side or you'll have double coverage on each end and only half as much paint in the middle. Sharron |
Plaster Stones On House: You would be much happier using Paper Clay instead of plaster. It is MUCH lighter and you don't have to carve it. Just apply to surface (wood) after rolling it out with a wooden dowel or rolling pin. Put some white glue on the wood to be on the safe side, even though it says it will adhere.... Then you will have plenty of time to press the grout lines in with the end of a popsicle stick or some other such tool. When it air dries, it will look just like stone! Then paint. You will love it and it is so lightweight! Kay Baughman |
Wallpaper: I like to wet the walls slightly with a foam brush first. It allows the paper to be positioned and moved and allows better adhesion. Also, should you have a problem, I use wallpaper premixed SEAM ADHESIVE instead of wallpaper glue and reinforce seams of prepasted wallpaper. Sue Thwaite |
Sealing: I plastered right on to the bare wood doors of my front-opening dollhouse and then carved the plaster to resemble bricks. This was over five years ago and it's still just fine, even with the constant opening and shutting of the doors (not always gently). Linda Roebke |
Sealing: A question was raised re: the sealing of a dollhouse prior to putting on the cement/spackling/mortar etc. to press stones into. Gotta seal it. If you don't, the water from the compound you're using will warp the wood and I think you'd end up having a mess. If you do one side at a time..... or a portion at a time and let it dry between putting other areas on...... you shouldn't have any problems using a sealer. Even priming it with paint will help. Connie |
| Previous 10 | Next 10 Page 685 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |