Plexiglas - I think there are probably lots of tips in the archives on making covers for dollhouses. When smoothing edges, use wet/dry sandpaper, progressing finer all the time and you can finish with hand rubbing the edges with toothpaste if you want it to be really spiffy. There are also lots of commercial polishes available. You can cut or drill Plexiglas, but you may have to experiment with drills, blades and speeds of operation for best results. If you cut too fast or too slow the stupid stuff melts and traps your blade.

Bonnie GIbson


Attaching Plexiglas: Look for a "U" shaped (probably more squared off) piece of metal in a hobby section or at a small hardware store. Take a piece of Plexiglas to make sure it fits in the channel. You glue the metal strip along the top and bottom edge of the area to be covered, then you put screws every 8 inches to support the weight of the Plexiglas.

A friend just showed me this method on the back of her wall hung dollhouse. Looks great.

Laurie Sisson


Attaching Plexiglas: We use Plexiglas and to attach it, we use Velcro... the self stick kind. This is a must, the "self stick type" or it wont hold up long. We use it on dollhouses, room boxes etc. You can cut it slimmer to edge just the edge of a room.

Billie Jo Eller


Aging copper: I always age our copper with salt and white vinegar. I use a plastic jar, pour salt in to about an inch and add vinegar. I let it set for a few days and then just use the vinegar to scrub on the copper. Don't stir it up and dip down into the salt. The scrubbing will then make it very bright and clean and if you wash it off is a good way to clean copper. Don't wash it off! After a few hours it will start to turn green, if it's not enough for me I then just paint the vinegar on--no scrubbing this time. You will see a big change the next day. Use an old brush and keep it for that. After time the solution in the jar will also turn green. I keep it for long periods of time as we use it in our workshops, also.

April


Flagstone / Fieldstone: Use a vinyl tile, not ceramic. You discard the top layer of no-wax surface and pattern. This is very thin and peels off easily, start at the corner. It is the body of the tile you want. When you buy the tile, look at it sideways, you will see the surface pattern you will end up with, and it will be white. That's why you want a tile that's "white clear through". Some are striated like stone, some have small indentations, etc. After peeling, this is the surface you will end up working with. Again to cut, just score with an Xacto knife and it pops at the seam. To make small stones, cut in long strips the width you want and use the chopper to cut equal size pieces.

Ruth


Quick and Inexpensive Gift: I bought a pair of plain unfinished bookends and decorated them. I put wallpaper on the upright (largest side) and carpet on the "floor". Then I bit the bullet and cut a coffee table in half, glueing one half to each wall. I put on the table and floor things I knew she loved, a cat, teddy bear, books etc. A couple of pictures on the walls and it was done. It took me one night to finish and it looked a million bucks.

Dee


Oilcloth:

1. Tape a sheet of wax paper or heavy foil to your work surface.

2. Tape your chosen paper [cut larger than final item it is to be] to the wax paper or foil on all 4 sides with tape about 1/4 on the surface.

3. Pour the Mod Podge into a flat container.

4. Dip a 1 - 1 1/2" foam brush in the Podge and spread a thin coat on paper in one direction only. Watch for bubbles.

5. Repeat. 4-6 coats on the sheet, drying thoroughly between applications.

6. For more drape-ability, do not Podge the back. If you are doing a floor cloth, podge 3 coats on the back.

7. Cut the paper into shape and size needed. Use podge to simulate wooden floors using paper that resembles hard wood floors.

or:

Transfer printed pictures to fabric. Photocopy desired picture. Coat the PRINTED side of the copy with a thick coat of opaque transfer medium, (Picture This, Modge Podge, etc.) Lay the COATED side down in the center of a piece of 100% cotton broadcloth. Flatten and smooth. Allow it to dry several hours. Using a wet sponge, gently rub the paper off. It is all off when the material doesn't feel gritty. Be careful not to rub too hard or the print will come off. Let dry and trim. It has a sheen and body to it like oil cloth.

Sandy in Alberta


Oil Cloth Instructions: The simple oil cloth directions are in the Miniature Collector August issue page 78 and the picture is in the June/July issue page 55.

Roz Weitzman


Gypsy Caravans: Contact: Midwest Carriage Co. PO Box 024, Mentor, Ohio 44060-0024, 1-888-281-3863 They have the wheels you are looking for plus a wonderful book entitled "Making Model Gypsy Caravans" by John Thompson.

Lucy Seiler in CT


Sites for Ceramic Art Tiles: There's Serious Inspiration here for anyone wanting to add authentic period detail or some contemporary flair. This is just a sample.

The first constitutes a great quickie lesson in differences among Arts & Crafts, Art Deco, Art Nouveau, etc. Also just a delight to look at: http://www.derbycity.com/michael/tiles.html

The second includes examples in style of Charles Rennie Mackintosh plus much else:http://www.artontiles.com/

Finally, here's one with contemporary-quaint-country-type designs - charming:http://www.saltillotilecompany.com/mural.html

Mary in Oregon


Previous 10 | Next 10


Page 701 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)