Etching Plexiglass: I admit this is not my idea. It belongs to Barbara Knox. She found that if superglue was contained in a plexiglass enclosure it (the fumes)? etched or "hazed the plexiglass. Take this one step further and if you protect the portion of plexiglass that you do not want etched (with wax perhaps)then expose the plexiglass to the fumes of the superglue; the unprotected plexiglass will be etched. Remove the wax and WOW.

Bob in Hollywood, FL.


AC Moore's Paper Mache Pumpkins: Someone else may have discovered this but they are NOT PAPER MACHE! I bought 2 on sale last August (originally $2.99, on sale at 25% off) thinking to make Cinderella's coach and a mouse house from them. I proceeded to cut the openings for the coach using a Dremel tool...gee it sure cut funny for paper...and what was this gray stuff that was being spit out at me.... PLASTIC! They are gray plastic, covered with one layer of brown paper! Once the integrity of the paper covering is breached, the paper falls off, leaving you with a gray plastic pumpkin. In order to paint the coach, I had to etch the plastic with automotive primer before replacing the paper,using Weldbond glue full strength. The same treatment on the inside allowed paint to stick as well but it sure was not the easy quick project I thought it would be! The moral of the story is..."thump" any paper mache shape that you are considering buying to be sure it really is paper mache and not paper covered plastic unless you are willing to go the extra mile to make paint stick to plastic.

Sammy (I'm a girl) Smith


Japanese lanterns: I am a cake decorator in my other life, and I saw a picture of a cake decorated in an oriental theme. It had paper lanterns on it made from the little paper parasols that come in cocktails. They had taken the stem off of two parasols and glued them open. Then they glued the two open parasols together to give a kind of lantern shape. I think it might be too big if you did it with full parasols, but perhaps you could carefully cut the parasols down before you glued them together. You could even change the silhouette of the lantern by how open they are when you glue .

Kellie in Omaha


Japanese lanterns: I just flashed on a plaster lantern project I had seen once in Better Homes and Gardens which was done over balloons. The oriental lanterns could be done the same way - use a very small balloon and Vaseline it. It is then removed with a lot less mess than clay.

Jacqui Marlin


Lite Brite Shapes: Old Light Bright shapes: Rounded end, then flared tall glass tumbler shape, often with trapped air bubble inside, 1/2 inch high, with a 1/2 inch high bullet shape on top, with a conical head. This bullet shape makes great perfume bottles, once sawn off.

New Light Brite shapes - Flat end (so they stand up on their own), fatter flared glass tumbler shape just under 1/2 inch tall, NEVER with air bubble trapped inside, then short fat pointed bullet shape, 1/4 of an inch tall. This short fat pointed end would make good mock fairy lights once sawn off - but it would not work as either a perfume bottle or candle, as there's more conical point than stubby body, if you see what I mean.

Helen from York, England


Chinese lanterns -- NN, maybe July (What would we do without Joann?? Get desperate like we were pre-SS while she was on hiatus!). Tissue tubes glued around a pencil, then slid down and crumpled to make the accordion folds. Could even make these working lights by slipping them over one of those holiday village battery-operated mini light strings. Another version you might try if there's a party supply store nearby is to buy those cocktail picks with honeycomb fruit toppings. Just snip them off the pick and glue a bit of wire in the top for a hanger.

Loretta Sniarowski


Hamster Accessories: We made hamsters out of pussy willows and cages with crushed cedar chips on the bottom, fimo food in Sudafed bubble bowls and with no cutting, just a little paint. We used clear lite brites, painted the bottom of the skinny part, where it connects with the larger part, black and the tip silver. Made a little wire holder and there is a great water bottle for the little hamsters.

Mary Lou in Portage, IN


Drilling Glass: There are a few ways to do it. The best is to use a small diamond drill bit in a Dremel tool - preferably with a drill press but not absolutely necessary. The bit and the glass should be kept cool - I wet a sponge and just drop a tiny bit of water on the work while drilling. Another way is to use any other kind of bit - carbide, or even copper. Take some plasticine clay and make a tiny ring around where the hole is to be, put in a bit of silica grit with water, and move the drill up and down in the slurry. This time the drill press is more important to keep the hole straight. I would think it should be fairly easy to drill into the thin glass used for minis. I have usually drilled thick glass which takes longer and is more critical. There are other ways, but these are the two I have used. All it takes is a bit of patience.

Jacqui Marlin


Drilling Glass: To drill glass you do need a special drill bit -a diamond bit - ask at your stained glass shop. It also helps HEAPS to make an X out of masking tape over the area you want the hole drilled. It prevents the glass front splintering into tiny, weeny slivers and, more importantly, stops the drill bit from skittering around before finding purchase in the glass - avoids any scratching if the bit slides. Also take it slowly and you should be fine. Just as a precautionary measure - wear eye protection just in case you get carried away and shatter the object - had a friend who got glass in her eye whilst doing stained glass windows - she semi-detached a flap of eyeball which required immediate surgery - YUCK!! She never did tell me if you can see what is happening during eye surgery or whether, being out like a light, you didn't know what was going on!

Trace


Drilling Holes in Glass: Here's the salient info from Dremel's 1981 publication, Compact Power Tools: Wear eye protection (maybe even face protection), use a tungsten carbide drill, lubricate with water and touch the bit down on the glass intermittently, to help keep it cool. Don't use much pressure. If the glass is thick, the author recommends also making a collar of clay around the spot where you will drill, and keeping this filled with water.

When you barely break into the surface on one side, turn the glass over and drill from the reverse. Repeat process, continuing to avoid overheating, until you break clear through.

Tungsten carbide drills are harder than the ones you may use for wood, and a bit more expensive. Personally, I'd give myself some practice glass to experiment on. Probably this is one of those initially intimidating operations that eventually seems pretty routine, though finicky. Good luck!

Mary (Oregon)


Previous 10 | Next 10


Page 721 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)