Thick Leather: Maybe a shoemaker can help with the thick leather you 're trying to "thin out". I've seen them trimming sole leather (thick), so maybe you can get help there. Joanne |
Brooch: I've been using single stud pierced earrings for brooches. Some are very small. If you want to buy a really small pair, the baby ones are nice. The pin at the back can be cut off some. Instead of the bulky backs that come with them, I use the tiny plastic keepers that come with lightweight French hook types. R. Roweblue |
For the moss between patio tiles, I would use the landscaping foam glued there. For the sand, guess I would put glue in the spaces and top it with sand! Rita Pierce |
How to thin thick leather: You could try to thin, or "skive" it, down to a more usable weight. I use a straight edge razor blade, but you can also use an Exacto knife, the sharper the blade, the better. Just flip the leather over, and use your blade on the flesh side of the leather to scrape off layers until it's as thin as you desire. It does take some practice to not slice through if you're trying for "really thin", it's not usually a quick job, and some cheap leather doesn't skive well at all, but I've successfully skived 3 mm thick leather down to paper thin. Michelle |
Brooch: How about using the magnetic earrings that give you the pierced look without the hole? You could place the back behind the shawl and the earring part looks like a fancy pin. Alberta |
Brooch For Shawl: A nice brooch can be made sewing about three little iridescent seed beads together and tacking them to close your crochet shawl. Or dig around in jewelry findings and/or cut a big one down to size. Pamela Swain |
Liquid Illusion: I got the Liquid Illusion at Jo-Ann's in the floral department.The main use for it is for filling up clear vases and then putting flowers in them. This is first time I have done any "water" and the Liquid Illusion was so, so easy! |
Picture Mats: Metal frames offer a look that is hard to get with wood especially if you are going to make them gold. By matting, any picture could work with any frame. Matting for miniatures should be easier than fullsize because the stock is pretty thin. You don't have a bevel to deal with that is as critical as full size. Here is my approach. Take your mat(any nice craft paper will do) and lay it face down. Place the print on it where you like it. Trace around the print. Remove the print and use a striaght edge to draw lines about 1/16" inside the traced lines. Use an Xacto knife to cut the center out following the inner set of lines - use caution at the corners. Now take another piece of paper cut to the size of the mat. adhere your picture to the second piece of paper so it is centered on the mat. Tape the mat and backing together. Also matting is not always used. Often folks drymount a picture into the middle of a backing and then place the mounted piece in the frame. Drymount uses a thin sheet of heat sensitive material that is placed behind the pic. I fuses when ironed.- of course any thing that works IE: double sided tape works. . bill |
Brooch for Shawl - since your shawl is crocheted, you could use a small piece of fine wire on the back of your pin, and just twist ends thru the open work! The front could be made from anything, a bead, bit of clay, a tiny earring, even a small silk rose, glued into the wire! Alice Zinn |
Mini bottle caps: I would suggest using a 1/8" round paper punch to cut rounds from heavy aluminum foil. Lay punched rounds on a giving surface (palm of hand, mouse pad, etc.) and push on their centers with a round toothpick (or other dowel) that has been sanded to a 1" (mini inch) diam. and that has a flat bottom. This will cause the edges of the rounds to flute up. Keep in mind that these will be very tiny (but in almost perfect scale) but if they are displayed with something else that will give a clue as to what they are I am sure they will suffice. Joann L. Swanson |
| Previous 10 | Next 10 Page 745 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |