Lightweight Bricks: I made an attic chimney for my farm house out of a chunk of smooth Styrofoam, that came in a packing box, for an appliance. Cut it to the proper shape, to line up with the one on the roof. Used a long bread knife to score lightly horizontally, then an Xacto for the vertical alternating lines. Paint the lines gray, then go over the bricks in your brick color, then do the gray again all over one side at a time, wipe off the gray. It gives a very realistic look.

MAP in Puyallup


Natural Supplies: I came across this website through work. I have no connection, but I know the guy who runs this place has a good reputation. It is called Avatar's World and they sell, through the mail, all sorts of dried flowers, but also florist supplies in bulk and pine cones, different seed pods, mushrooms and ornamental grasses. No pictures because the site is under construction, but they do have an 800#. The address is www.avatarsworld.com. Hope this helps for those who are looking for these supplies.

Kathy Ostrander


"Lightweight" stone work: Have you tried working with the lightweight spackle that comes in a plastic tub; from any hardware or home improvement store? If not, you should check it out. It dries very hard but is very lightweight! You will, however, have to make an original mold to work from. You should find plenty of tips, etc for mold making in the small stuff archives. Any of the available molding materials should be suitable for the purpose.

Lloyd Cooper


Cold Press Illustration Board: Brooke uses Crescent brand I believe.

Bob Francis, Calgary, Alberta, Canada


Lightweight Stone; a method I learned in a fireplace workshop some time back might work for making "rock" siding for your castle.

Spread Spackle or Polyfil on the sides, pulling it up into peaks as if icing a cake. Let dry and set up for a couple of days. Using a sharp instrument, score lines to suggest rocks. Brush over lightly with a wire brush to round off the peaks.. Stain as desired. The stone fireplaces we made using this method look quite believable, and Poly fill is not heavy.

Rita in Beautiful B.C.


Hollowing Logs: Someone did the most adorable 1/4" kitchen scene inside a rolling pin at the Birmingham regional. What she did was take a quarter of the pin off. She left the sides and handles intact and made a cut halfway down the center of the pin and halfway through the front side. To visualize this take a circle and divide it in four quarters. Remove one quarter wedge and you have the back and bottom remaining while the wedge you remove becomes the area for the scene. Have I lost you yet? What the woman did, who made the rolling pin scene, was get a piece of plexi glass to replace the wedge she removed, and this protected the scene she made within the pin.

dee dee


Lightweight Stone: I made a castle recently and I painted the outside wall in a light grey and sort of "mottled" it by dabbing on with a small sponge some white and other shades of grey. Then I used that stone colour, that has this sand stuff in it and I put that on fairly thick as if it was an individual stone i.e. the base colour would be the grout and then I put on some kind of square stone (pretty irregular though) move a millimeter further and put on the next "stone". Another possibility is to cut up squares from a paper mache egg carton that has some "bumpy" structure on the inside and give this a thin wash of "stone-colour".

Heike Boam


Castle stones: A good way to make stone look things is to use a paper mache type stuff.

You can make a plaster mold by carving the stone shapes into it or by pouring the plaster over a clay representation of a stone wall. Since you are wanting to do a whole house/castle this way it would be efficient for you to make the mold. You can even do the fancy stone work around windows this way. Once the mold is dry you can grind up shredded up paper in a blender with enough water to make a oatmeal type goo. Drain it in a strainer so its not too sloppy. Put it in the mold and press it down well with a sponge to remove the majority of the water. Once it is dry it will pop out of the mold. Then you can glue it to the walls using regular tacky glue. You can fill in the gaps between sections with a flour paste like you may have used in kindergarten. To paint it you can use the sponge technique someone else mentioned or you can purchase a lovely acrylic paint from ceramic shops. Gare makes one called stone stuff and Duncan also makes a similar product but I don't recall the name of theirs. These paints have a multi-colored granite like look to them and couldn't be easier. You just brush it on and walla it looks like stone.

Marsha Hedrick


Wood Size: Sometimes we have to cut down from true scale to make it look right as you described in making your kitchen cabinets. You seem to have tried to use 3/16 stock, but 3/32 is close to 1" in scale. Full-sized wood that is called 1" is actually nearer to 7/8" or less, so the mini wood actually should be a bit thinner than 3/32nd.

June Simpson


Dollhouse Kits: As a general rule, I think the more expensive the kit, the easier it is to put together. The first dollhouse kit I put together was from Real Good Toys with Houseworks components and it was easily assembled and sturdy enough to be a family heirloom 20 years later. The second was a die-cut cottage; it took three times as long to finish and the result is only a quarter as good. My Dura-Craft San Franciscan went together easily and I thought their use of channel moulding for the corners was very clever. Then, I got to the roof where the pieces don't fit together properly around the tower and noticed the whole structure was leaning toward the left. They have since come out with a "new, revised version" but I'd guess the weight on the left still pulls the house out of shape over time. Laser cut kits go together very easily -- even the micro-minis. They're sturdy and the trim pieces are wonderfully detailed and elaborate. So for a beginner, I recommend going with RGT, Walmer or laser cut. Die-cut houses take more patience and skill...

Sally Cook-Thomas


Previous 10 | Next 10


Page 829 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)