Store Floor: Someone mentioned using wide craft sticks for plank flooring. If you do this there are a few things to consider. First is that these sticks tend to cup when subjected to water based(white glue) and they often tend to stain unevenly. If that is all one has, then go for it, but if wood like basswood strips are available I'd go that route. I just did a floor with nice old poplar and I used the pieces that were cracked. Once finished, the cracks added to the old look. I feel one of the most important decisions you can make when building miniatures is the wood you use! 1/16 works well. I used 3/32 this time around, though, simply because it was the thickness of the wood I wanted to use. If you use craft sticks make sure you sort through them. Avoid any with wide graining as these are the ones that tend to cup.

Bill Leimberger


Building MDF Houses/Kits: If you decide to use screws, (recommended), make sure you pre-drill and countersink your holes. If you sink the screws slightly below the surface, you can cover the holes with wood filler and sand smooth when it dries. If you use nails, pre-drill also because the MDF will split out if you don't. Use glue in both cases. Don't be scared. Go for it! Wood filler and paint cover up a lot of goofs.

Spencer Stall


Making Paper Plants: Years back, many of us learned to use an inexpensive office-type club punch to make geranium florets. Even though the punch-out has three rounded "petals" and one that's squared-off, it still works quite well both for small blossoms and for leaves. The McGill company seems to have replaced the old club die with a slightly bigger one; so much the better if you can lay hands on both. Hearts and diamonds (and the less-useful spades) were also in this series, as well as rounds in two or three sizes. Even now, I think you can find them for under $3. Craft stores carry McGill's new "Punchline" series (around $10), which includes a wavy-edge "blossom" and a crisply pointed star.

Fiskars is getting into the act, too. The squeeze-handle design of all these punches is desirable, because they'll handle card, foil, and thin veneers as well as paper. If these punches have a catcher for the bits of paper, take it off. Then pre-mark your paper (even pre-score with a ballpoint tool) and turn the punch over to center it over the markings. Much simpler than trying to add colors to all those tiny bits of paper. If you want to punch more than one sheet at a time, it's easier to separate the pieces if they're different colors.

But box-style punches have some virtues. The price is right, especially with sales and money-off coupons, and there are lots of designs. (For example, there's one with three different sizes of wavy-edge rounds: perfect for the biggest leaves at the base of the plant working up to smallest ones near the top.) One caution: be sure to keep your sales slip until you make sure a new punch cuts cleanly.

Mary (Oregon)


Chinking for Log cabins: when I chinked my loghouse I bought caulking made by "frost king" it looks like a solid roll but actually its a strip that pulls apart in 1/4" strips, just place and push in seam then using a slim flat paring knife go along both edges and it smoothed out evenly and flat. Made a big difference in appearance.

Alice Prosky


Finishing hardwood floors: When using the flooring sheets from Houseworks or Miniature House, you must be careful putting a wet stain on them. The moisture can peel off the paper backing that they are attached to. So if I like the color of the wood as it is, such as Oak or Walnut, I just put a coat of Butcher's Wax or another clear paste wax on it. Wait a little while and buff it. Now if you want to enhance the color you can use shoe polish in a color. Just buff it. If you want it to really look great put another coat of clear wax over the shoe polish. I find the floors look really fantastic this way.

Lorraine Scuderi


Log Cabin Chinking: HBS sells logs made of pine that are perfect for facing a dollhouse shell.

When I put together a log cabin room box for the catalog, I made the chinking but cutting 1/4" strips of foam core. I painted them with ivory enamel paint, glued them with the foam facing out between the logs and then pressed them with the flat end of a cuticle stick. The foam compressed and the edges spread out unevenly and it had just the right look. My e-buddy, Pat Townsend, came up with a better idea: She used real caulk and squeezed it out into lines on wax paper and let it dry. She then was able to peel up the lines of caulk and press them between her logs. She said it looked great.

Sally Cook-Thomas


Chinking Log Cabins: Of course each region would use a slightly different mixture according to what is available at the site. Mostly it is a combination of clay or soil, grass or straw or even tree leaves and small twigs. Sometimes dung was added for stability.

The cabin I grew up in was chinked with clay mixed with straw. When that dried it was coated over with a plaster of pure clay. Then planks of bark were pushed into the wet clay so it acted like mortar to hold the bark in place. The bark acted like shingles keeping the rain (It rains a lot in Oregon) from washing away the chinking.

Chinking in miniature can be done using paintable caulk available from local hard ware or home improvement store. The caulk comes in several colors, Off white, brown, white etc. Cut the end of the tube off at an angle and as small as possible and still get a good stream of caulk. Run this between the logs. Smooth the caulk out with a wet finger then to add realism sprinkle with dirt or model rail road dirt. Some of the Eastern and even Southern log cabins were chinked with white (Lime) as was used in plaster.

Bill Hudson


Finishing sheet flooring: When using a wax to finish the wood flooring that comes on a sheet backing, I use steel wool (#0000) to apply the wax. It sands as it finishes, no pre-sanding needed. I use Bri-Wax which can be purchased at most woodworking stores or from their catalogs. Bri-Wax comes in clear and 3 stain colors, so you can sand, stain and finish in one step by applying with steel wool, then wipe with a paper towel (this buffs it to a satin shine). It also doesn't show any overlapping. It comes in a Simonize type can and a very little amount on the steel wool goes a long way. Keep in the fridge when not using and apply while still cold. I would suppose similar brands would work the same. Its amazing what a smooth and beautiful finish you get. People will think you labored for hours when it took only a matter of minutes.

Mary Kay Gentile Ft. Myers, FL


Mini plants: Someone (not me) is going to suggest that you use a bonsai in your terrarium! While that might work and would truly look like a mini tree, it might be tricky to keep it alive in that sort of setting. There are bonsai shops in your neck of the woods, I'll bet, and they might be able to suggest a plant that would thrive in dampness. I've been a bonsai hobbyist for years, but our conditions are completely different here in Arizona and what works for me probably wouldn't work in New York. Some plants you might consider: a small juniper, cheap and available at your local nursery, can be trimmed up to look like a tree if you choose it carefully (look at the main stem or trunk) and might work for you; another plant that springs to mind is bald cypress, which would look like a redwood tree and does love wet feet- they'll grow in standing water if they have to. Also, one of the small bamboo varieties would be happy in a terrarium. For any plants, you'll need a full-spectrum light in your aquarium/terrarium. These are advertised as plant lights and simulate daylight.

Pat


Board Materials: Matte Board is a heavy card stock used to mat pictures. It is not meant to be painted or glued. Illustration board is a heavy card stock that is meant to be used for posters, signs or graphics and is meant to have paint, ink or glue on it. Foam core is two pieces of lighter card stock with a layer of foam between them. It can be painted but will warp easily. Gator board is a plaster type board with a fine foam between them and it used by museums and graphic artists for signs etc. It is meant to be painted, inked or glued so it will not warp easily. Obviously, illustration board and Gator board are best for building. Illustration board comes in two thickness’ and so does Gator board. The late Gail Vaughan used foam core which is cheaper than Gator board when she made a wall that was meant to look like adobe type building because she covered it with a layer of joint compound which strengthened it.

June in London Ontario Canada


Previous 10 | Next 10


Page 830 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)