Wiring: You should prime with paint before you do any wiring. The way I do my ceiling fixtures is to either use a canopy (designed to plug in and hold ceiling fixtures) or run the wire through the ceiling to the floor above and attach to electrical tape (it's hidden under the flooring or carpet). Jan |
Dremel speed control: I ordered my speed control for the Dremel from Micro Mark. I also have the hanger that clamps on the table and suspends the flex tool from about 2 to 2½ ft above the table, from Micro Mark. It is so handy. Fannye |
Glass bricks: You might be able to make an illusion of glass block using plastic canvas with the threads removed to make the size block you want and adding some clear silicone in the spaces. The canvas should be flat on a sheet of wax paper. When dry, you could pull it off. I have never tried it, but, I think it might work. Mary |
Making Artificial River Run Rocks: Mix Durham Rock Putty up until it is just thick enough to handle. Roll it out into a ball about the size of a golf ball then cut it into marble size pieces (don't roll these out). Place the pieces inside a large round bottom plastic bowl with a lid on it. Before placing on the lid, add a couple tablespoons of dry putty powder to the bowl. Then shake the bowl around a bit. This should give you some boulders. Dump them out onto newspaper to dry. Repeat the process by cutting down some of the marble sizes into smaller pieces and shaking them in the powder again. You have usually half an hour to work with it. You can repeat the size cuts until you nearly have sand. When they are completely dry you can smack a few with a hammer to crack them. To vary the color a bit get powder dye, used to mix in cement for color, from a hardware store and mix in with dry powder. Bill Hudson |
Glass bricks: I have seen the smaller pieces of clear Lego used and didn't realize it as Lego. Looked pretty cool in fact. Also, Hobby Builders Supply out of Ontario makes sheets of clear plastic in grids of various sizes. They have various sizes of squares on these You could water down Tacky glue and paint that on the back of one of these to give it that opaque look and the front would still remain shiny. That could work. Debi |
Easy Outdoor Ferns: Craft stems are pipe cleaner-type materials sold in packets (sometimes hanks) in the U.S. and Australia, but maybe not everywhere. "Bump chenille" craft stems have a thick and-thin profile that, if you squint at it, resembles a string of end-to-end fern fronds. With a bit of scissoring and nipping, plus paint and wire, you can use these for quick-and-easy ferns that work well as foundation plantings on the north side of old houses, etc. Start with a packet of green or light-colored stems. Use small thin-bladed scissors to clip the fibers from two sides of a stem, making a flat piece. Squeeze fern-green paint onto your thumb and forefinger and moosh it firmly into the fibers. This makes them clump together, resembling individual leaflets. These tend to "grow" in one direction, which should be toward the tip of the frond. Cut the painted stems apart so that each has a relatively short tip - in other words, like a fern. The opposite pointed ends will be too long but don't chop them off yet. If you have a reddish-brown felt-tip on hand, make a faint mark along the length of the stems - not vital, but a subtle improvement. Assemble fronds by wrapping wire around the lower part of one, positioning a second opposite it and wrapping around both, adding a third facing the edges of both, and so on. Splay the stem ends out horizontally for a base, clipping any excess length. You can glue each (I like E-6000) on a scrap of card and add your choice of soil before the glue sets up. You might also like the effect of single bumps left unshorn and upended as tall plants in your flower border. Leave unadorned (not everything is in bloom at once!) or shear the leaflets at the tip even shorter and add buds or small blossoms. You can use other pipecleaner-type materials the same way. |
Ripping Lumber: Here are some safety rules associated with this practice. First, and most important, NEVER put your hand beyond the center of the blade. If the strip kicks back it can push an unsuspecting finger into danger. ALWAYS use a push stick when cutting thin strips. Lower the blade so that it is no more than 1/16 inch above the work. Learn to rip pushing with your right hand only. You are less likely to twist the wood with your left hand causing binding and kick back. After you turn the saw off make sure the blade has come to a complete stop before reaching toward the blade to pick up your work or remove scrap. Pete |
Potted Topiary: The potted standard topiary made from a skewer, green landscaping foam, and a styro ball is the perfect entry-way plant for many settings. But sometimes you need something less formal and tightly pruned. There are other materials you can use for a more open effect. Mostly, you need to glue something into a styrofoam ball, rather than on top of it, which means poking holes around the surface of the ball to secure the greenery. Possibilities for greenery include individual plastic leaves, short pieces of craft-stem "pine" or similar material, other craft-store greenery from garland or sprigs, or dried natural materials. As a nicer alternative to styrofoam, you can start with a pod from a sweetgum tree (liquid amber): these woody brown seed-holders are usually globular but vary quite a bit in size and shape. Zap them in a microwave, nip off curly tips, shake out the dried seeds, and use the resultant holes to glue in a trunk and greenery. The conical shapes of teazels can be used the same way, except that these come with their own trunks; just sand off the thorns. (Teazels aren't as ubiquitous as sweetgums, but sometimes show up in craft stores.) Other areas are sure to have other plants, including weeds, that'll work the same way. If you have space to grow a pot of oregano in summer, let it go to seed and then dry and paint the stalks and seed clusters, shoring up with several coats of acrylic medium. These are a great way to suggest those little pots of standard rosemary you see in decor magazines. Mary |
Logs: For 5/8 half round logs, try contacting a dealer who carries Celerity House dollhouses. Celerity is back is business again with new owners and they manufacture that type of log (or at least it looks that way)...but be forewarned they're pretty pricey. Kathy |
Paper Punches: Ruth Hanke at HankyPanky crafts sells paper punches as well as punched bits by the bagful if you do not want to purchase one of the more expensive punches. I have ordered from her and was delighted with the very fast delivery. Her website is at http://hankypankycrafts.com Maryann Cipriano |
| Previous 10 | Next 10 Page 833 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |