Gluing Styrofoam: I have used Liquid Nails or that type of glue for Styrofoam

Roz Weitzman


Logs: For your 5/8" half logs, find someone with a table saw and have them slice the appropriate sized dowels in half. If you are careful it can be done pretty easily. Attach the dowel to the edge of a scrap length of 1" x 2" or what ever flat stuff you have with masking tape in several places. This way when you slide the dowel / scrapwood across your table and into the blade, the dowel won't turn and rotate and give you a crooked cut. Remember you will lose a thickness of your dowel equal to the thickness of your table saw blade, so you may want to buy dowels slightly larger in diameter than you want the finished width to be. Hope you can understand my computer drawing below:

saw table/wood/dowel -blade slices only center of dowel, NOT scrapwood
-(blade here)
_________lllllllllO__________

Bonnie Gibson


House of Miniatures: According to their ad in DHM, the HOM Collector Society's web site is http://www.miniatures.com,/p>

Their mailing address is in Atlanta, GA.

Nutshell News published a number of kit-bashing articles over the years, many of them by the late Ron Benson, and several HOM kits were featured.

Kathy Watkins


Grandt Line: The address for Grandt Line I have is: Grandt Line Products, 1040 B Shary Court Concord CA, 94518, Tel: 925-671-0143 Fax: 925-671-0806

Judy Bayless


Molding for a log cabin: First of all, don't let ANYBODY at a lumberyard treat you any differently than they would some guy walking in there. Remember that some "guys" don't know which wrench to use to pound the screw into the board.

Second, 5/8" molding may be an odd size. Look for companies that specialize in molding in the yellow pages. They do make dowels in 5/8" size, but if worse comes to worse, use 3/4" and fake it. Remember that a 3/4" log would be 9 inches in the 'real' world, and that's about right for a log.

You could also use screen molding, which is about the same 3/4 width, with slightly rounded edges. I have a book on hewn-log cabins that shows almost exclusively that the logs used were square, and a lot of those cabins were in Kentucky, Tennessee, and thereabouts.

Karen Isaacson


Half round logs: Try the half round molding and you will find it comes in many sizes. Look in your local Home Depot or the equivalent.

Charlean


Grandt Line: The URL for Grandt Line is http://www.mria.org/companies/Grandt.html

Rose


Glue: For anyone who uses glue in a tube like Goop, once you've used the glue that first time the cap always seem to get glued to the throat of the tube and you can't remove it.  Next time you use the glue, wipe off the throat with a paper towel and smear Vaseline around the throat and screw on the cap.   It's amazing how easy it is to remove the cap the next time.

Paula


Toolbox item: Haven't noticed any mention of Clotilde's Handy Seam Guide. It is sturdy plastic, has several measurement guides on it, that can be used for inside or outside 45* corners, and for measuring widths down to 3/8. It is 2-1/4 x 2-1/2 so fits easily in the tool box. My new Clotilde's sewing catalog (not mini) arrived today, so I thought of it. Check out www.clotilde.com

MAP Puyallup


Damaged MDF: MDF fibres tend to absorb moisture (from acrylic paint or gesso) and swell. So you probably won't end up with as smooth a surface as you started with, especially if you have sanded the MDF - as this will take the flat shiny surface off. However you ought to be able to compensate for this by using some sort non water based filler to even up your surface. I use the modeling putties used by plastic/metal kit modelers. Fill/rebuild any damaged areas, let dry then sand smooth. You may need to repeat fill if you are trying to fill a deep gap like where you slipped with a saw because the putty will shrink a little.

I have used several brands: Tamiya Modeling Putty (from Japan), Humbrol filler (From UK), Squadron filler (from USA)

These all come in a tube like toothpaste. The first two were grey - good for filling metal models but may show thru on lighter surfaces. But by far my favourite is the Squadron in comes in white & green - I use the white for filling MDF and styrene. I haven't used the green but I figure it would be good for colour control especially over/under red paint (just like the green tinted concealer makeup for hiding veins & blotchy skin).

I wouldn't go sniffing the stuff tho - it contains toluene and has very interesting warning labels on the tube.

Sandra


Previous 10 | Next 10


Page 834 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)