Glass Beads: You can also get a nice mix of glass beads from a company called BeadBox. They have a mix of about 130 glass beads from the Czech Republic that I have combined with other smaller beads to made perfume bottles and Christmas tree ornaments. They do have holes, so I usually use headpins snipped to size to hold all in place (glue too). This mix is $9.99. Their toll free #is 1-800-BEADBOX. I didn't see a web site listed.

Judi


Warped roof: I have done some restoration work in the past, this method worked for me. Provided the warp isn't to extreme. Try nailing the roof down to a truly flat surface, so that it is once again "square". If you have a steam iron with a heavy steam output you can apply the steam to the roof. You will want to make sure you really saturate the wood of the roof (you will have to remove any paint or shingles first) with the steam. Leave it nailed down for at least a week or more. You could reapply the steam during that time to help reshape the roof. If you don't have an iron with a good output you could try renting a wallpaper steamer. I had good results using one.

Lloyd Cooper


Lincoln Logs (for Log Cabins): I was in the Toys R Us store this AM and they have oodles of Lincoln Logs in sets for all sizes of buildings.

Elise


Dollhouse Factory: Here is an interesting site to look at-- it is "To Dream of a Dollhouse" and is a dollhouse factory in miniature.

http://www.geocities.com/salssite/to_dream_of_a_dollhouse.htm

Marlene Chapman in Ontario


Little Floss Flowers: There's another flower you can make with embroidery floss that Frieda Gray doesn't mention in her book. It's goofily simple, and not the least showy. (I rather like the notion that not every blossom is a diva.) All you do is take a piece of floss - say, six inches - and tie a series of tight knots in it,maybe a half-inch or so apart. Cut apart right next to the knots; then trim the loose strands to about a quarter-inch long, for example.(Some of you may agonize over measurements; I avoid the issue by making plants!) You can stiffen the strands if you like. Paint the knots a green to match your stems, and glue on - facing up, dangling, or whatever. (There is at least one shrub - witch hazel, perhaps - that has small hanging flowers quite a bit like this.)

Mary (Oregon)


TIP using fluid to mask off wood to get marquetry effects

This is American stuff named 'Incredible White Mask', also known as 'Liquid frisket'. It is a form of liquid or white mask (generic terms). Any art supply shop would carry this. It has a shelf life of

3 months and will change composition if it sits in the sun or freezes. It comes in a small container, the size of nail polish.

Deborah wanted me to veneer a table for her with a fancy cardinal points doodad on it. I said I wasn't competent enough to do it. But like a true miniaturist, she knew what she wanted, and had her moment of mini magic. She drew a circle in the middle of the table, masked off the rest of the table with 'Incredible White Mask' (IWM) and inked in the cardinal points symbol. Once dried, she took off the IWM, and IWM'd the symbol, staining the rest of the table. When she removed the IWM from the middle, it had absorbed some of the ink she had used to color the symbol, but this gave it a pleasant weathered look.

The thing that fascinated me was that there was no 'bleeding', of either ink or stain, to the other parts. Therefore one could make a backgammon table, make marquetry patterns on furniture, a chess/checkers board, make a parquetry floor... I once tried to do a real parquetry mini floor with veneer. It looked good, but the cost in blood, sweat and tears doesn't bear the telling.

Helen


Foamcore: Comes in thicknesses from 1/16" to at least 1/2". It is easy to cut with a SHARP Exacto knife. Sheet sizes also vary from 20 by 30" to 4 x 8'.

However, I do not recommend using it for building dollshouses. It warps. It can bend. It's not all that strong. If you don't want to use a wood product, you might try Gator board for a small house. This product can also be cut with a sharp Exacto knife, but it is much stronger than Foamcore and does not warp. However, it will dent under pressure. Gator board is sold via art supply houses and frame shops and mini shops can get it from Dee's.

Beth


Warped Wood: I managed to flatten a piece of warped wood by soaking it in water and weighting it down flat with three cast iron weights of an old weighing scale. Weight it on a hard, flat surface - my surface bent and my wood warped in the opposite direction so I had to repeat the whole process.

Tracey


Copper Sheeting: Real Good Toys sells small, thin sheets of copper for dollhouses...it's about 1 square foot, can be cut with scissors, and even aged for a verdigris look.

Laura in OKC


Copper Sheeting: Copper sheets can be obtained from K&S Metals. Most miniature shops have access to this through Dee's. It is tooling copper and 3 square feet if memory serves me right. Or try any good craft store or train shop. They often have it too. Also a very thin copper sheet about 8" x18" may still be available from Real Good Toys. I think we have some in stock.

Sue


Previous 10 | Next 10


Page 835 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)