Cutting a straight Line: What I discovered was if I wanted a truly straight line, I lined up my "metal" ruler and took several shallow cuts with the Xacto knife against the ruler, rather than trying to cut through with one deep cut.

Suzi


Foamcore: You can probably use Foamcore to make a roombox as long as it's not too large and you are careful about preventing warping. If you apply a water-based product to one side, apply a water-based product to the other. Examples: paint both sides; or paint one side and use Tacky glue on the other. You don't have to do it at the same time, but don't wait too long or it will warp.

In addition to gluing the foamcore together, I would stick some straight pins in to hold the edges and maybe even tape the seams, then cover the outside with fabric or something to cover it all up.

Beth


Foamcore: I just finished teaching a class on building a two story English Tudor Cottage which was built from ½ inch foam core and turned out great no warping and a lot easier to work with than plywood. This is the first house that I've built using

½" Foamcore but it won't be the last. I will agree that the thinner 1/4" and 5/16" Foamcore does have a tendency to warp if not stiffened with beams or siding. When I built my Buttercup I glued 5/16" foam core on the outside to thicken the walls since it was a tab and slot house with very thin walls. So there it is, properly used it is a great building material but used improperly it can be a disaster.

Rik Pierce


Warping: Soak the piece in water, place it on the garage or driveway floor and park the car with one wheel on it. Leave overnight (walk to the grocery store). If it is a large piece, cover it with a larger piece of wood. Place wax paper between tire and wood if you care about car tracks.

Fannye


Foamcore: I have used foamcore for smaller scale houses and room boxes and it works great. Much easier to work with than wood for those of us who are "power-tool challenged". In the States, it is carried in office supply stores such as Office Depot as well as some craft stores.

Elaine


Foamcore: When using foam core it is necessary to coat both sides to prevent warpage. Wallpaper one side and paint the other, as long as you coat both sides with something.

Sylvia Brinkley


Cutting Dowels in Half: If you decide to cut dowels to get your half round, you will probably need one size larger such as a 9/16" in order for your finished half round to be the correct size (1/2" wide.) You have to allow for the material lost in the actual sawing process - what is called the saw kerf which is the thickness of your saw blade. Also to do the job safely and to prevent the dowel from twisting while you cut, the safest way is to tack your dowel down front and back to a scrap length of flat stock such as plywood.(Put two small brads or nails into the sides of the dowels- not the middle- so you don't cut through your nail.) You will end up sawing through both pieces at once. Run the straight edge of your flat stock along your table saw guide and you should end up with an even cut.

Bonnie Gibson in Tucson, AZ


Foamcore: I love foamcore. Another great medium to use to make walls and structures is the 1/2 inch insulation material that places like Lowe's sells. It comes in a 4 foot by 8 foot sheet and doesn't warp. You peel off the thin plastic coating on both sides, and you can cut it with an exacto knife or shop saw.

Anita Myers


Foamcore: On the subject of foamcore, Michaels carries two sizes. I think it is 1/4" and 1/2". Also I have used my table saw to cut foamcore and it works great. Just had to sand the paper a little bit. Have a 2 story General Store plan and I wanted to do it with foamcore and appreciate all the remarks about it in this digest. I just made a Sorcerer's Spell Book of foam core and really like it to work with. Made the base for the book to sit on out of it and used a granite texture ceramic paint on the base and my daughter said it looked like marble. I did not notice any warping but the granite paint was not that wet.

Elizabeth Cooper


Foamcore Thicknesses: Foamcore comes in 3mm, 5mm and 7mm and you can buy it from art shops, Staples used to carry it but I think they have discontinued it.It comes usually, 30 in by 26 in,sorry to mix up the measurements. Have used it a lot , I use it for small box scenes.

Hazel Dowd


Previous 10 | Next 10


Page 836 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)