Painting Foamcore: This is a trick used by watercolorists, works with foamcore, too. Use plain water on a brush or sponge to dampen the back of the foamcore before painting. The wetness of paint makes the foamcore's paper covering expand or shrink or something, which causes warping. If both sides are damp, they both expand (or whatever) and the piece stays flat.

Lee Menconi


Foamcore: Regarding the questions about foamcore - I am by no means a 'pro', but several years ago I built a garden shed from instructions in Nutshell News, and I was very pleased with how it turned out. I used a band saw to cut it nice and straight (but you can also use a utility knife) and then lightly sanded the edges to get rid of the paper fluff. Following instructions I was able to make that foamcore look like cobblestones, cottageboard and even siding on the outside. I used it to make the inside pieces as well - cupboards, counters, shelves, everything! It's light and very easy to work with. One hint though, when painting, (I used water based paints) don't get it too wet, for it will warp. Just do several very light coats instead. I did warp my floor, so I lightly sprayed it with water, covered it with wax paper, and put heavy books on it for a few days. It worked!

Jan


Builders Foam: I cut the foam (lots of layers) on the scroll saw just like it was butter. The foam stuff carves so nice. The latest carving tool I've discovered is one of those knives that you use to cut the V's in a watermelon. It makes a nice little groove in the foam and it's super easy to make it look like stones or rocks. We used hot glue to assemble them in the class, but tacky works if you have more time. You might want to tape the pieces if you use tacky cause they tend to slip and slide. We painted ours with a coat of creamy yellow paint with sand in it. Then I antiqued mine with acrylic washes scrubbed in.

Bonnie Lavish


Blocks of Foamcore - Try the home supply places like Home Depot or Home Base and look at the 2 inch insulation Foamboard used to insulate houses (real ones) it's a lot cheaper and very easy to glue using construction adhesives such as Liquid Nails. A 4' x 8' sheet costs about 20 bucks and you will have enough foam to build Mt. Everest. I use it to build my castle towers it's light, strong and easy to work with. You can cut it with a sharp knife or use a table saw or scroll saw for smaller pieces both work great. I personally find it indispensable in building and scenery ( hills and things).

Rik Pierce


Cutting Dowels in Half: A band saw is less dangerous FOR THIS CUT. If you do still want to cut the dowel in half, get a scrap piece of straight wood and temporarily glue the dowel to the scrap. Hot glue is good for this. This way there is something to keep the dowel from twisting, which is the dangerous part. Use push sticks to keep your fingers away from the blade. Miniatures are hard to make without fingers. While I don't believe power tools in general are particularly dangerous, you do need a healthy respect for them. It is just that I think cutting a dowel in half on a table saw is a dangerous cut for someone without experience.

Dean Jenson


Fimo/sculpey: I like to mix equal parts of fimo and sculpey. If you have a pasta machine it is very easy to do. The pasta machine conditions the clay and is much more easier to work with. I use this method for making my dolls.

Bonnie Justice


Wood Warping - Solid wood moves with moisture content. In a heated house it will lose moisture and shrink a little, but not evenly. If you could see the growth rings on the end grain of a board they would be curved. As the wood dries out the growth rings tend to straighten. The only way to stop this is either to maintain the moisture content or capture the lumber by force. This is why dovetails on full scale pieces are marked and cut the same day the lumber is milled. This is also why it is proper to have the concave side of the rings on the outside faces of a box or drawer to keep the edges from pulling apart as the lumber dries.

Solid wood is not like fabric.... You can make it flat by ironing it or training an elephant to dance on it, but, unless you stress the wood and damage the structure, it will reassume its original shape.

It may stay flat for a while, but beware... unless you glue it or fasten it in some other manner it will almost always resume its bow.

Pete


Cedar Wood Source: IBEC in British Columbia sell miniature cedar wood- shakes, strips, all sorts. Their catalogue on computer is: http://www.ibecwoodproducts.com

Laura


Promat is basically the same as Fimo and Sculpey, except it is suppose to have more strength. I really haven't found the others to be weak, but I use Promat for sculpting animals. I have found that it is easier to get fine details than with Fimo, and Sculpey is too soft. The texture is just right - kneading is much easier than using Fimo. I haven't checked lately, so I don't know if the craft stores have it. It's made by the same company as Sculpey.

Mary Eccher mentioned the problems with realistic color when using Sculpey, and I don't know if Promat is the same in that way because I work with white. There is a newer clay called Premo that is also made by the Sculpey people, which comes in an artists color palette, and I have seen that in Michael's.

Cheri Stewart


Picture Frame/Molding Source: For picture molding, instead of getting the basswood molding handled by Dee's and most miniature shops, try S.H. Goode & Sons, 8830 San Gabriel Road, Atascadero, CA 93422. They handle several kinds of wood, and if you get their catalog, you will see the wonderful selection of woods and styles of molding. It costs a little more, depending on the kind of wood, but I got maple, walnut, cherry, and rosewood. They make up into very nice frames. Their email address is wood2scale@thegrid.net. Also, their Just-a-Clamp is excellent for making frames, too. Take it from one who has made hundreds of frames.

Olivia Wassmer


Previous 10 | Next 10


Page 837 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)