Bricks: I cut up popsicle sticks and used a combo of red-orange and grey paint mixed with sand and some glue to make the color I wanted. To add the finishing touch, I used a black wash to make them look old (a trick I learned from a friend.) To my surprise, when you add the bricks to a thick wood putty base which has been painted with grey or white paint, you have a pretty realistic brick wall. |
Fimo and Sculpey mix well together. Although all the Polymer clays have a bit of variability in their baking temperatures, it is slight enough to be forgiven when mixed. Mary Kaliski |
Chrysnbon kits: For glue, Testor's "Model Master Liquid Cement for Plastic Models" does a great job. The bottle comes with a long, skinny spout, so you can put one drop of cement exactly where you want it, or run a skinny little line of cement right along an edge. Bought it at a store that sells model car kits. Whatever glue you get, make sure it's for styrene. Lee |
Cheap roombox - IKEA is selling unfinished frames for 3D pictures, named BAS. They come in two sizes Small 6 ½ x 4 3/4 x 3 inches deep Big 11 ½ x 7 ½ x 3 inches deep The smaller one has a fixed glass front, and one fills the frame from the back. But the larger one has a sliding glass panel for the front. What this means is that if you buy 2 (they retail for £6 ea in GB), bash out the back of one, remove the glass from the other, and glue the empty back of one to the glassless front of the other - voila, your roombox is suddenly 6 inches deep, so you have a decent sized room box for £12. It also means that you can reinsert the glass panel you removed, so you could etch a ghost on it and/or stick things to the surface of the glass, giving great "depth" to the roombox. The potential is so great. Helen of York, England |
Hollow Pumpkins - Instead of the lethal Styrofoam why not try a ball of aluminum foil. after it's baked it can be squished (like that word?) smaller and removed. Or you can use the kind of "peanuts" that are made of cornstarch and dissolve in water. Gail Spector |
Gluing tiny leaves to the ground: I haven't tried this, but this is what I would try. Mix white glue with water until it's thin enough to spray (Windex bottle or equivalent). Spray glue to cover surface. Be kind of liberal with glue. Sprinkle leaves over wet glue. Roll lightly with a brayer (a rubber roller) to set the leaves into the glue. Tom Berkner |
Fimo pumpkins with foam balls: let me first give you a WARNING. When you make anything that will melt foam balls in the oven, the fumes are VERY toxic!!! If , as you say, you need to make a lot of them it could be downright dangerous. I make them for my park classes and here is the best way I have found to do it. I use a toaster oven and I always take an extension cord with me and set the oven up OUTSIDE where I won't have to worry about the fumes. Anyway, here is how I do them. I buy the smallest foam ball they make at the craft store (I think they are about 1/2", never measured them) and you kind of mash them to the shape of your pumpkin. (Pumpkins are never perfectly round). you condition the clay and roll it out to about 1/8th inch thick. wrap it around the ball and smooth off all creases. take the back of a knife and make your dents from top to bottom all the way around. stick a stem of your choosing (I pre-make the from fimo, but a stick is ok) into the top. with a single edge razorblade I then cut the "lid" but leave it on to bake it. It is much easier to carve the pumpkin before baking it, but if you want the kids to carve their own, take out the melted foam ball, return to the oven just long enough to warm them up a little and it will be easier to carve them after they get hard. Good luck, and be careful of those fumes. Norieta in Hawaii |
Pumpkins: watch out for the Halloween lights as well. I have seen strings of jack-o-lanterns, all you would have to do is cleverly place them so their faces were hidden. Also, found a cute pair of earrings at the dollar store, very teeny jack-o-lantern - it could be used as a decoration of some sort. The pair I bought, however, are decorating my ears (what a concept...;) lol!). They also had teeny little grave markers as well, for anyone interested in 1/4 Halloween. Marbles for pumpkins: I bought a bag of marbles last year for various fimo projects. Most of them were too small, but there was the odd shooter in there (which is about 1/2 to 3/4 inch big). Would make a small pumpkin, anyway if you can find a bag that has one or two of the shooters included. Okay, quick everybody, tell her what we can do with left-over little marbles! My suggestions are a tool for making fimo items like bowls, crystal balls, modern art and forms for small hats. Kim Bulback |
Gluing jewelry: I love to use epoxy to repair jewelry and many other things. It is durable. I prefer the 5-minute quick set up kind. I've used this to fix earrings and to make an entire "tree" of old jewelry that I use at Christmas time. W. Marie Werth |
Hollow Pumpkins: Some years ago when my friend Judi wanted to make hollow pumpkins, I gave her some sculpting wax that I had here. She made wax balls and then made the Fimo pumpkin over. When she baked the Fimo, the wax melted and she had a hollow pumpkin. Had a bit of a messy tray too, but not too difficult to clean or can be lined with tin foil. And the wax can be used again and again. I expect any soft wax could be used, not just sculpting wax, but I *know* that the sculpting wax works. I was certainly impressed with the end product! Joy |
| Previous 10 | Next 10 Page 839 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |