Wood source: I recommend SH Goode & Sons, PO Box 2575, Atascadero, CA 93423-2575. Email is wood2scale@thegrid.net  You can get a catalogue by sending $1.50. They have all sorts of neat wood and very good service.

Beth


Wood mail order:  Hobby Builders Supply is on the web at www.miniatures.com, and so is Northeastern Scale Models at www.nesm.com. The latter has nice mouldings and mini birdhouse kits and 1/144th scale houses also.

Karen Isaacson


Brass jump rings: Rio Grand has Silver and Gold filled jump rings in 2.4mm 1-800-545-6566. If I need small ones, I just make them myself.   It’s quite easy, and really inexpensive.  Any jewelry manual will explain the procedure (basically you just wrap wire around a tube or rod of the right size, then cut them with your jeweler's saw).

Tom Berkner


Thin Glass: Someone mentioned using microscope slides. They are 3 mm thick. Some have a section of ground glass at one end of the slide. For ULTRA thin glass try using the cover slip for the slide specimen This is optically clear and is much, much thinner than the 3 mm slide, some where around 1/2 mm.

Bob, Hollywood, FL


Dean Jensen/Thin Glass: I'm sorry to say that Dean Jenson is no longer doing miniatures due to poor health. This was in his last Newsletter to me in May. A loss of a very talented man. However, he has sold portions of his business. Thin glass is now being carried by: George Wrisley, 17784 SE Paradise Drive, Milwaukie, OR 97267 (503) 653-2591. He also sold his Roo Glues and Rainbow Design Items in 1"; 1/2"; and Quarter Inch items to other people to continue.

Ruth, Grass Valley, CA


Thin Glass: Microscope slides are not what one would want to use for window glass. They are a bit thick. Cover slips are VERY thin (.13mm to .25mm) and could work as individual panes in a window. I've found them at various scientific supply firms (VWR, Daigger, Thomas Scientific) in various sizes (20x20mm, 20x30mm and 20x40mm). If anyone is looking for "portholes", there are also round cover slips available (15mm and 18mm diameter generally), but these are pretty expensive. I think someone still makes a plastic cover slip, but the ones I used a few lifetimes ago turned yellow. Science-wise they were the pits .... miniature-wise they were worse than the pits. I did use a hole punch to make small circles for mini "spinning aircraft propellers" from them, but was not that pleased with those either. I'd avoid any plastic ones you may find .... unless they're free.

Howard, Concord, CA


Mini Blinds: Go to a home decor place or section of a dept. or discount store that carries place mats. You will probably find some that, cut up, will make lovely mini blinds! Hang them and use very thin string to make the long loops that go around them to raise and lower them!

Alice Zinn, Pt. St. Lucie FL


Very Thin Glass: For those of you who have requested it, I now have the 6oz glass on my web site http://www.dollhouse-miniatures.com under Catalog>Bldg. Components>Windows and Door>Components. This is .027" thick (thinner than veneer). This is thin enough to use in the doors of your china hutch (in 1/12 scale). The next size up at about .040" is micro glass.

Tom Berkner


Quarter inch stained glass windows: For the leading in stained glass windows try one strand of black embroidery floss and glue. Put the plastic ("glass") sheet over your pattern. (I reduce/photocopy from full-sized stained glass patterns to get quarter scale.) Then using a toothpick or needle-pointed scribe, put a thin line of glue down the black lines (lead lines) in the pattern. Start from the middle of the pattern and work out. When the thread lines dry, you can go in and paint the stain into the various blank spots. I do both sides this way which makes a very lifelike looking window.

Pat


Plywood: The Home Depots in this area only sell 3/8" fir in different grades. One of the problems is these tend to be 3 ply, plywood, which warps if you just look at it askance. You want 5 or more plies to help the stability. The grain of fir, also "telegraphs" through wallpaper and most other treatments. This can be alleviated to some degree by sealing and sanding before assembly. Given the choice, I would pick MDF before fir plywood for a dollhouse.

Tom Berkner


Previous 10 | Next 10


Page 843 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)