Plywood: Most Home Depots (if not all) sell birch and oak plywood, but not in 3/8" thick. They usually handle 1/4" (in an AC or AD - one good face) and 3/4".

My Daily Diatribe on Plywood - Best to just skip by, unless you are a real glutton for punishment or just need to pay penance for something!

The Baltic birch (or Russian, or Finnish, or European) is 9mm (very close to 3/8").It is commonly available in B, BB, BBB grades. Typically used by cabinet makers for drawer sides and bottoms and for the backs of cabinets that won't be seen. so dollhouse manufacturers use it. Seems to work well. I find the 5' x 5' size to be annoying. Difficult to handle, and most plans are laid out to fit 4' x 8' sheets. 3/8" nominal plywood today will vary from 11/32" to 3/8" which means you really need to make allowances for this when cutting. I measure the thickness of each lift (84 sheets of 3/8") and vary my plans to accommodate. That 1/32" in thickness isn't much until you add it up over the 3 floors in your dollhouse, and suddenly the attic partitions are 3/32 of inch too tall (that's why some manufacturers don't include attic partitions) or the length of the roof is 1/16" too short (or long) because of the thickness of the end walls (most manufacturers overhang the roofs - even though it's incorrect for a colonial home; just so they avoid this problem.)

As you may have noticed, the price of plywood is quite variable. So far, I haven't seen any two prices on this digest which are talking about the same sheet of plywood. There are A1, A2, BB, AC, domestic Birch, Baltic Birch, Fir, etc. We haven't even bothered to mention the cores (except # of plies) which can vary drastically in the allowable knots, voids, splits, and type of woods (seldom is the core of the same hardwood as the faces) except in Baltic birch or the method of making the face veneers.

Personally, I find that an A1 domestic birch with a J or K core works very well. I use both rotary cut and flat sliced. For my less expensive series of houses, I use 9mm, 7 ply obechee with an obechee core.

A typical wall in an older house will be a 3-5/8" (or larger) stud, covered with 3/8" lath on each side and 3/8" plaster over that, giving a final thickness of 5-1/8" (newer homes are 4 1/2") 1/4" plywood gives a scale thickness of 3", while 3/8" plywood equal 4 1/2". 1/2" plywood would be 6". Floors would typically run 9 1/2" joists, 3/4" lath & plaster ceiling, 3/4" subfloor and 3/4" hardwood floor. In scale, you would need 1" plywood (might be a little heavy) so we cheat and use 3/8".

Tom Berkner


Plywood: I have found that the 1/4" plywood from HD does not seem to warp (at least for me) if I cut it up as soon as I can. Do not lean it against a wall and leave for any amount of time and expect it to be straight. As for the 3/8" plywood, our local HD carries a luan plywood that is really smooth on both sides and doesn't seem to warp no matter what. It is rather splintery on the edges, so be careful handling it. Also, if you are cutting cross grain (usually the width) make sure your saw blade is SHARP. It will eliminate a lot of splintering.

Ron Gill


Speaker boxes: I used an old speaker for a scene last year, and liked it enough to buy more. The ones I've gotten so far are quite sturdy, but pose a couple of design challenges. They have reinforcing blocks on the inside corners that you have to fit your inner walls around, and if you want to keep the nice finished front edge, you pretty much have to put the glass in first, then assemble your scene from the back. If somebody has solved this one, I'd love to know how! (And if you figure out some cool stuff to do with the speaker innards, too. They're starting to pile up.)

Lee Menconi


As for removing labels on Midwest wood, we don't have a problem. We carefully remove the label with an X-acto knife or fingernail, allow the residue to air dry and them simply rub it off. If the wood is old, then it takes a bit of sanding. Very seldom do we get a piece that is a problem.

Sharon Stockton


MDF (Medium Density Fiberboard) is stable and paints wonderfully on unmachined surfaces. It is quite heavy, has little tensile strength and doesn't hold fasteners very well. It also has a tendency to get furry when cut or sanded. I don't think the toxicity is any worse than plywood. If you can figure out how to cut the openings cleanly and don't mind the weight, it will work fine.

Pete Boorum


MDF stands for Medium Density Fibreboard - that brown stuff not unlike super fine chipboard in its construction. It's really smooth on the surface and looks for all the world like big sheets of compressed sawdust. I find it really good for dollshouse construction and I've never had any of the problems with end nailing and stuff but I do rout a groove to sit floors and the like in prior to nailing.

Tracey Joy


Bending Wood For a Spiral Staircase Handrail: Steam the wood and wrap it around a piece of plastic pipe (maybe 4" drain pipe) and hold it in place until cold. To be more precise, take a piece of plastic pipe, and make a form on the outside of it for the handrail. You can glue and screw thin pieces of veneer onto the pipe, above and below where you want the hand rail. Steam the wooden handrail for about 10 to 15 minutes. Working quickly (with gloves, remember the wood is hot) position the handrail into the form and clamp it into place. Let it cool for a couple of hours.

It is best if the pipe is smaller in diameter than you want, since the wood will relax some when you unclamp it.

Tom Berkner


Bending Wood: I use bending plywood (also called crazy plywood). The 1/8" (3mm) will bend around a 4" pipe.

Tom Berkner


Bending Wood: I used to work for Timber Turn, who make all the craftwood items for folk art that you get from places like Lincraft Spotlight. You know - the round boxes, trays, wooden hair clips etc. and that sort of thing. Well they steam the wood, shape it for whatever they want and clamp it with bulldog clips. If you use single ply this bends quite easily and your idea of wetting the wood and clamping should work OK.

Tom Berkner


Bendable or crazy plywood bends much better than any solid wood. I have found it in 1/8", 1/4" and 3/8" thicknesses. The 1/8" is what I use. The particular ones I buy have a birch face veneer (about 1/100" thick) and the other layers are luan. All the layer run in the same direction, except the face. I have taken a 4" diameter plastic drain pipe, and wrapped the plywood around it without breaking. No, there is no boiling, steaming or special treatment necessary; just bend it. It only bends in ONE direction. The only place I found to buy it is from my plywood wholesaler. I would be happy to sell partial sheets to anyone that would like to try it. Shipping is not a major problem, since I can roll it up and put it in a box. The cost of 1/8" will be $1.50 per square foot.

Tom Berkner


Previous 10 | Next 10


Page 844 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)