Build your own "Cookbook" from my Website: You asked if I still have my project booklet. I haven't had those for years. When I was writing the Mary's Menus articles on Fimo and resin for Nutshell News, I put that booklet together from copies of the articles. Well....as the number of articles increased, it became very costly to continue the booklet. BUT.....for anyone interested in learning about modeling compounds and resin in miniature cookery, I have a plan and I hope you will like it. As of today, my WORKSHOP link at my web site http://www.pannikins.com/ was uploaded.....the very beginnings of it anyway. There you will now find information on ALL ABOUT MODELING COMPOUNDS, ALL ABOUT RESIN (dispelling some of the misinformation out there), the GINGERBREAD MAN project, and the WITCHES' BREW project. The EGG NOG will go up there tomorrow. This is just the beginning. My intention is to post many, many more projects (for the novice as well as for the advanced student) to my web. Each and every project at the Workshop link will be fully able to be printed out easily. Therefore, those interested, can compile the projects into a folder of some sort and create their own instructional miniature cookery book. All I ask is that these projects not be used for monetary gain, either by submitting them as articles of your own to the magazines, writing your own book using my techniques, or becoming a dealer at a show creating just my projects, instead of using your imagination to create your own. Yes, all these things have happened to me in the past 20 years. You are welcome to use the projects for your own use, club projects, or to develop your own talents with your own projects using the techniques mentioned...and I truly hope you do so. Mary Eccher |
TAMALE WRAPPERS: could you use the inner-most layer of real cornhusks? They are much more flexible and delicate than the darker green outer layers. Loretta Sniarowski |
The best "shredded" coconut is made by drilling holes in lucite or plexiglass, and salvaging the shavings. Size of shreds, of course, depends on the size of the drill bits you use. Mary Eccher |
SAND, fine craft sand now comes in colors. Makes coating on fried chicken in yellow/brown, sugar in colors for cookies, mix it into paint for textured finish...let me count the ways.... Laurie Sisson |
Cream of Wheat - my suggestion is to use a translucent material like silicone and mix in white sand on the top surface. The other suggestion was to use cream-colored floral tape for tamales. Jacqui Marlin |
Oatmeal/Porridge: I made the best looking porridge by accident. I was making cinnamon rolls using Crayola's Model Magic. I had tinted it off white using acrylic paint, and we'd used real cinnamon. Well, in the process some of it got a little too dry and I was experimenting. I broke up some of the pieces and put them in a container and mixed in some glass stain - probably clear. The glass stain seems to soften the Model Magic, and by stirring several times, I got porridge. Marsha Heeter |
Filling wine bottles: I have been filling wine bottles with 'Burgundy Wine' (or Grape Juice), resin. Now how many of you have tried this? The resin is just thick enough, that it did not 'flow' in a nice tiny stream! The bottle openings are so small. It is a little tricky! I ended up having to drip it in with a very thin wire! Barb Lewis |
PUMPKIN PIE Sculpey - white Fimo - Ochre and Orange Artist's Chalk - Ochre X-acto Knife Toothpick Fimo Matte Lacquer Miniature Pie Tin Knead a bit of ochre Fimo into white Sculpey until a pie-crust color is obtained. Roll a small ball and press into pie tin (as you would with a real pie). With an X-acto knife, trim any excess from the rim of pie tin. Cut the point off a toothpick, and use this to flute the edges of your pie. Bake pie in oven at 250 degrees for 10 minutes. With X-acto knife, shave a bit of ochre artist's chalk into a powder. With thumb, rub this powder around the fluted edge of pie for a "baked" look. Then paint edge with Fimo Matte Lacquer. For filling, knead together one part ochre to one part orange fimo. Roll a small ball and press into pie crust until even and flat. For whipped cream, roll a very thin snake of white Sculpey and place this around the edge of the pumpkin filling. To texture, make triangular indentations in the snake with the flat side of the very tip of your X-acto knife. Bake entire pie again at 250 degrees for 10 minutes. NOTE: For colonial pumpkin pie, spray the pie tin black and leave off the whipped cream. Mary Eccher |
Wrapping Mini food: I have only recently begun to make mini-foods to place in my mini-kitchen/refrigerator. I have a thing for details, so my thinking was, I would never put certain foods in the "fridge" without putting saran wrap around it, so my mini-yummies needed to be covered too. So, I put a small piece of saran wrap around the food (some on plates) and I twisted the wrap on the bottom. I then cut most of the excess away while holding the "twist" in place, which left a small bunch, that was of course too bulky for realism. So, I took a lighter and waved the flame several inches under my item until the saran wrap did kind of a "shrink wrap" around the food! It only takes a second or two and you can press the still warm wrap tight to the item to get a tighter fit. I used this method to wrap hotdogs, bacon, cheese, plates of brownies, etc. I also had purchased a loaf of mini-Wonder Bread that came with no plastic wrap around it. I covered this in Saran Wrap and held it over my stove burner to get it to hug the loaf somewhat. It looks so realistic now with a tiny red thread tied around the opening for the "twist tie". Of course, these "shrink wrap" tips needs to be exercised with caution, as fire will burn you!!! Someone may know of a better (safer) method, but this works for me! Karen in Cary |
Halloween Project - WITCHES' PUNCH This is, by the way, an actual real-life Halloween punch. When you mix Orange Kool-aid with Purple Kool-aid (with Ginger Ale), you get a black Halloween Punch. Materials Needed: Polymer Compound Resin (the 2-bottle kit such as Envirotex-lite. One bottle is your resin, the other is your catalyst) Black Opaque Color Paper Cup, Stirring Stick, Toothpicks Chrysnbon Punch Bowl Kit Baking Crystals - clear (for ice cubes) In a paper cup, pour one part resin to one part catalyst, very equally. Add to this just the tiniest touch of Black Opaque Color. STIR THOROUGHLY. Carefully pour catalyzed mixture into your punch bowl and drizzle mixture from the tip of a toothpick into cups. Add "ice cubes" and then set aside to cure and let harden for at least 24 hours. Options: You may want to place a mini skeleton, candles, etc. in your punch to spruce it up. Do this as soon as you have poured the resin mixture, then add the ice cubes. Any of the materials used above should be available at your craft or miniature shop, or can be ordered at my website. Wish I could import a picture of this punch to SS, but that is not possible. If you are interested, I will send more projects using fimo and resin to SS, and of course, I will have them at my website. HAPPY HALLOWEEN! Mary Eccher |
| Previous 10 | Next 10 Page 862 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |