Dying white doll hair fantasy colors: Is the doll hair natural fiber? If it is, I have your answer. Don't laugh - -- Kool-Aid. Wonderful fantasy colors. Easy to find. Cheap. What more could you ask? I use it all the time. Mindy Skelton |
Dyeing dolls hair: It depends what kind of material the dolls hair is. If it is natural fiber like mohair or silk,it will take the dye very nicely. If it is artificial fiber, you will have a problem getting a deep tone. For colours like purple or pink on natural fibers - Kool-Aid (the unsweetened kind) works great and you only need a few minutes. Actually any food coloring is great on natural fibers. You can also experiment with natural dyes like onion peel, tea, oak bark, walnut shells, beet root or elder berries - even a ropy red wine.... And of course all the Rit dyes work great too. Heike Boam |
Dyeing dolls hair green or purple: If your doll hair is real mohair or some other "real" fiber, you could use a fabric dye. A word of caution though, very hot water might shrink your fibers. Also, try not to agitate "hair" too much as this could cause a tangled, matted mess! BTW, if "hair" is man-made fiber, I wonder if you could use some of those sprays that are made for coloring artificial flowers. "Design Master " is one brand that I've seen at A.C.Moore. Michael's might carry them too. Joanne from South Jersey |
Hinges: The hinges that I made are in 1/12 scale which does not alter the method of fabrication. The tools and materials I used are; Needle nose pliers, Dremel moto tool with a cut off disc, Small sharp scissors Straight pins (as in sewing) Ruler; obviously (steel) The material I made the hinges from is sheet brass; only because I happen to have some of it. The hinges can be made of any thin material. The thickness of my sheet brass is a bit less than 1/32" or 1.0mm. The hinge that I made is a Barrel hinge. one side of the hinge has a single barrel and the other side of the hinge has 2 barrels. The single barrel fits between the barrels of the side that has 2 barrels. A cut off straight pin is used as the "pin" for the hinge. It is passed thru all three barrels and cut off to fit the distance from the top of the topmost barrel to the bottom of the bottom barrel. The head of the pin is left on so it (the "pin") will not fall thru the barrels. HOW TO MAKE THE HINGE. Remember I made this in 1/12 scale so adjust accordingly; The completed hinge started out as two (2) individual pieces of brass sheet measuring 1/4" by 1/2" for each piece. Find the center of the pieces on the 1/2" side or 1/4" in from each end. Lay a straight pin along this center line and fold the piece of brass over the pin. do this for each piece of brass, 2 pins, 2 pieces of brass. You now have 2 folded pieces of brass with a straight pin held at the fold. Use any tool (blade of a screw driver) to firmly press the brass down for the length of the fold so the pin is secured. Now pull the pin out of each piece of folded brass. This leaves you with 2 pieces of folded over brass measuring 1/4" on a side. Take the two embryo hinges (;-)) and place them back to back so the barrels are facing in opposite directions. Like two number 9's back to back. With the needle nosed pliers or any holding/clamping device without any ridges on its jaws (hard to find) clamp the back to back pieces of brass just at the point where the barrel and the flat(plate) meet. Holding the 2 hinge pieces in this way, place two lines on each barrel so that the 2 barrels are divided into equal 3rds. Then use the Dremel cutoff wheel to go completely thru the long barrel cutting it into three (3) equal sections. After this cut has be made you can release the clamping devise and now come the magic. On one of the hinge halves just remove the middle section. The section that has cuts on either side. On the other hinge piece remove only the two outer most sections. NOW put the pieces back together by fitting the remaining sections into the areas that were occupied by the removed sections of the mating half of the hinge barrel. Slip the straight pin into the tubular axis of the meshed barrels and lo and behold a hinge. I will admit it is a simple plate hinge but from this point on you can make any type of pinned hinge you desire. DrBob...Delray Beach, FL |
Hinges: You need to find Pete and Pam Boorum's website (which I can't find the address for right now). There business name is Smaller than Life (I'm pretty sure). Anyway, I took their class at the NAME National convention in Charlotte last year and it was called "Hinges without Hassle" and was great! They have a very specific method for applying hinges and it works and I actually did it. And they have two nifty little tools that you use in the process (both of which are very reasonably priced) and they make all the difference in the world. One is a very tiny drill bit held in a little collet that you use to drill starter holes for the nails. The other is a slant-ended pair of tweezers with a slot in one end for picking up and holding the nails while you guide them into the holes. http://www.nh.ultranet.com/~smallife Mary Lynne in Huntington, WV |
Firing Miniature Doll Legs: In regard to the firing of small legs, etc for mini dolls; there is a doll stilt caddy which is in the Lou Davis catalog. I understand that this works very nicely. I think it is put out by Bell ceramics. They have two different sizes and the prices are reasonable. There is also an egg caddy that might work real well. Sandy |
Hinges: In light of my previous posting here is my method for putting in hinges. When I took the Ralph Partelow piano workshop, he had us glue the hinges on because the nails split the fine cherry, mahogany or walnut wood. Hinges don't really look right with the hinge plate but no nail. So, when I got home, I used a TINY drill bit in my mini hand drill (you have to be careful not to push because it is no more than a hair) and pre-drilled a starter hole for the nail. Then I inserted the nail (with a touch of glue to secure it) with a pair of needlenose pliers. The glued on hinge plate was held in place and did not move around as I worked and the predrilled hole lets me insert the nail without undo force resulting in split wood. Ana |
Finishing furniture kits: during the week-end I projected and assembled one night stand in Italian style. On January 28 it's programmed the first ADMI workshop in Verona (the city of Romeo and Juliet) and I will teach how to assemble and finish a furniture piece. As during the workshop we will not have enough time for staining the wood, I made the night stand using walnut sheet. I tried also a quick finish, to avoid the long shellac finish, also I don't like my night stand in a gloss finish. After assembling and gluing the stand, I applied a coat of wood sealer. After one night I sanded with steel wood and I applied one coat using "Floquil" flat finish. It's very difficult to find Floquil paint in Italy, normally I buy in Switzerland, but for you living in US this is not a problem. After the paint was dried, I polished with a soft wool cloth and applied the final finishing using liquid wax. Floquil flat finish is a wax based paint and the final looking is very nice. Pierluigi |
Stilts: I make my own stilts using ni-chrome wire and ceramic clay for the bases. I make a star shaped clay base, and I make each stilt about 3 inches high. These stilts, after initial firing to cone 05, can withstand repeated firings up to that cone size. Just be sure your glazes fire no hotter than cone 05 (there are lots of neat ceramic glazes to try). Make sure your stilts are about 1-2 inches apart and you can fit lots into one firing! I also use these for china paint firings as I can string 2-3 heads on each stilt. Each base has up to 8-9 stilts Nada Christensen |
Bashing Michael’s Hutches: I took top and bottom legs and frills off, left doors on, filed (using new Dremel) the protruding areas on the sides, glued three of them together, flush in a row and have them in the back of my store. They are painted purple, yellow and blue. One day soon I'll get them on my web page. I'm very please at how they turned out. Kathy Henry |
| Previous 10 | Next 10 Page 884 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |