Lighting kits: Hobby Builders Supply has them in their catalog. www.miniatures.com

Leslie


Soldering:  When soldering use "rosin core solder", and buy a tube of rosin as well. Never use acid solder, it is for plumbing only and will corrode your wire. After you have stripped the insulation off the 2 pieces of wire (or copper tape if you must use it), wrap them tightly together to form the joint. Apply some rosin to the bare wire, it will both clean the wire and help the solder flow. Then apply your hot soldering iron to the wire and bring the solder to the joint. It should freely flow onto the joint, and should be shiny bright. Any excess rosin can be wiped off with a paper towel. Remember, apply the soldering iron to the wire, then add the solder. You need to heat the wire so it will allow the solder to flow all around it. This is an almost instantaneous process.

Barb Jones, Cupertino, CA


Switches: When you cut the tape for a switch everything beyond the switch is controlled by the switch as you noticed. I make the cut as narrow as I can, so my fixture will be straighter. Anyway you need to bridge this gap successfully to allow the system to work. Make sure you've put the switch together correctly and that there is a prong in each tape run. A way to avoid this for a ceiling fixture and only control one room at a time is to run a piece of tape from your main tape to the ceiling place where you want the fixture. Put the slit in this wire only and not in the main tape. Then it will control only the ceiling fixture.

Deanna, Thiensville


Wiring:&nsp; You sure can 'mix and match' brads and eyelets in your Cir-Kit wiring layout! Wiring seems to be one area of our hobby that newbies feel so intimidated by until one takes a class or does that first wiring job then it sure becomes easy. 

I used to calm customers by telling them that they would not be electrocuted by dollhouse wiring, and in most cases, they couldn't burn down their dollhouse, either - LOL!   These were my 2 biggest fears until I did it myself, anyway!

Laura


Wiring: I've noticed that several people have questions about wiring. Cir Kit put out a booklet called Tape Wire Instruction Book that is very good. It can be purchased at HBS for $3.95. There is also one on round wire. HBS also has a Wiring Instructional Kit that along with an audio tape and video tape and material to practice with that is only $9.95.

Rusty


Electricity:   I wire everything!!  I have once to often wished I had in retrospect , so I wire things that at the time you may not think need wiring. I use the small long bulbs for box rooms, I can't think of what they are called but you get them at lumber stores.  I have never been disappointed since I made the decision to always wire.  After all once you catch on it is not difficult and if you think you don't need it, don't turn it on.  I think everything I've wired looks better for it.

Kathleen in Colorado


Brads vs. Eyelets: I like to use the small eyelets to make connections, rather than the brads. Because the brads are pointed, any expansion of the MDF (or plywood for that matter) tends to force the brad out of the hole. The eyelets (when properly installed) are straight, and therefore just get tighter as the wood expands. Now, for the big question; How do you install them properly? "I'm glad you asked." I said.

Earth & Tree just happens to manufacture a tool (actually a modified automatic center punch) which is designed to install the eyelets without mis-shaping them (as pilot punches do). This tool has a square tip which is the same diameter as the inside of the small eyelets from Cir-Kit. This keeps the eyelets from collapsing when being inserted. The square end keeps the wood from splitting. Have you ever watched a finish carpenter installing small pieces of trim. When nailing close to the side or end, you will see that he first hits the point of the nail with the hammer; this dulls the nail so it will tear it's way through the wood, rather than forcing the grain apart as a point will do. Also a point will follow the grain, which is why you have nails sticking out the side even when you started them straight. As you push on the tool, you compress an internal spring, which when it reaches its limit, will expand suddenly, pushing the tip into the wood, thereby inserting the eyelet.

Since you don't need a hammer, you can even use this tool in bathrooms and hallways. This tool works equally well on plywood, MDF and solid wood. A second tip is available for inserting the large eyelets for outlets (receptacles - or power points). If you don't obtain this tool, then I suggest you drill a hole 1/16" diameter (or slightly under) using a piece of tape on the drill to mark the depth of the hole you want (just the length of the eyelet). Then insert the eyelet using whatever method you like (push pin, pilot punch, needle nose pliers). This way works fine, but is a lot of work.

http://www.dollhouse-miniatures.com

Tom Berkner


I highly recommend Tom's eyelet inserting "ConnecTool". Yes -- he invented it. It forcefully gets those eyelets in at your tape connections and for your light connections, without pilot holes or drills. And the eyelets stay in much better than those maddening brads. He sells it at his site: http://www.dollhouse-miniatures.com

Anne Gerdes


Brass Tubes for Lamps: I recommend using 1/16" tubing, but you should get the ones from Special Shapes that have a .007" thick wall (rather than K & S with .014") which gives an extra 1/64" internally for running the wire. You could even go with the 5/64" tubing for a little more space.

Tom Berkner


Auralights: Check at Home Depot or a similar store. Builders Square used to carry them, but they have gone out of business now. They were in the section with light bulbs and fluorescent tubes. Also, I believe they used to be advertised in the miniature magazines. They are great for lighting room boxes. The shortest length they come in is 10", I think.

Doris in San Antonio


Previous 10 | Next 10


Page 901 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)