Auralights are available through Dee's and can be ordered by your miniature shop. They are a mini shelf lite and good for lighting a roombox or shelf in a cabinet. I only carry the 10" version, but it also comes in 20". They are available in black or chrome, or white or brass. Jackie |
Lighting Theory: Why lights quit working. Many people have had difficulty when using tape wire and making connections with brads. Doubling up the brads does seem to help. When the lights go out, usually all you need do is tap the connections with small hammer. My view (based mostly on logic - not great scientific experiments) has to do with the shape of brads and the characteristics of wood. When wood absorbs moisture it expands (MDF more so than plywood). The expansion of the wood pushes against the tapered point of the nail, forcing it from the hole/wood. (You can experience this effect by placing some cooking oil on the tapered end of your ball point pen. Then grab the tapered end and squeeze. The harder you squeeze, the faster it flies out of your fingers.) Every time the humidity/moisture cycles, it pushes a little more. Finally, the brad no longer makes a connection with the two pieces of copper tape. If you used the small eyelets, rather than the brads, you should have better luck. The sides of the eyelets are parallel, so the force exerted is equal, and doesn't push it outward. Now, if you used a pilot punch to insert the eyelets, they probably deformed to take the tapered shape of the punch point, so you have the same problem. It will probably take longer to happen because the increased surface area creates more friction so it moves slower. If you drilled holes (gives parallel sides) and inserted your eyelets, you should not have this trouble. If you used the eyelet insertion tool to insert the eyelets, it also keeps the sides parallel, thereby helping to minimize this problem. Tom Berkner |
Failing Lights: One of the first mistakes I made wiring was in my large farmhouse. It turned out that I had to many lights (bulbs) for my transformer to handle. I read the directions . I thought very carefully, but misunderstood the difference between fixtures and actual bulbs. If you are using a transformer that calls for 50 lights, that does not mean fifty fixtures. Most transformers come with built in fuses, and an overload will cause the lights to fail. They may initially light, but then fade and go off after about five to ten minutes, and they won't come back on. and if you have fifty bulbs, the transformer still may not necessarily keep up with the load. This is only one other reason why you may be experiencing problems with lights not responding. Tom Berkner gave a very good explanation in regards to installation problems. using a probe will tell you whether to not you have a good connection. If you think your transformer might be deficient, you should then consider dividing your system into more than one transformer. Carol Wagner |
Chandeliers: I make crystal chandeliers. I can make chain and electric wires as long as needed. To see my web site, go to SS digest's web page and click on links. Then under Accessories, click on Marvelites. If you send me a snail mail address, I will be glad to send you a brochure. Joanne at the Jersey Shore |
Installing Outlets: First, soldering the connections is no doubt the best way, but also the most difficult and time consuming (and you need a soldering iron). For outlets (receptacles) we use the large eyelets, inserted with the second of my tools. These fit the large plugs that come on the inexpensive lights. This doesn't work well on the die cut (Greenleaf et. al.) because the eyelets are too long and go all the way through the wall. The hammer in outlets from Miniature House are short enough to work. Because of the tapered nails, you may have the problem I discussed before. Cir-Kit makes an outlet with nails also (but it requires that you buy their plugs). Again, these have the tapered nails on the back. If you like to solder, you can solder a short length of wire onto the tape wire, and solder the other end on to the nail on the back of the outlet, before you hammer it into the wall. That should continue to work even if the outlet falls off the wall. Tom Berkner |
Foamcore & electrical wiring: I have wired two very large houses and innumerable shadow box's and vignettes made of foamcore. I have yet to have any problem. Considering the first one was built in the early 70's, I think you will understand my lack of concern. In this first house, I used a technique popular at the time, and ran the cords through the walls by making channels with a coat hanger. That house still lights, so relax, enjoy! Becky |
Ventilation: It was wisely suggested to me that when you electrify a house or room box, make sure the heat has a way of escaping. So in my DH, each window is open about a half inch to allow air circulation. Sure would not want a fire, since I have no firehouse - yet! Barb in PA |
Light up your life (or your dome) >I could run the tape wire on the bottom but where would I put the splicer? Forget the junction splice. Get the lead-in wire that has bifurcated lugs (horse shoe shaped thingies - that’s the techie name) on both ends. Use a couple of wood screws underneath to fasten the lugs to the tapewire. You may need to put some short legs underneath to raise the base just a little (many hardware/lumber places sell "screw plugs" which are about 1/4" high). Tom Berkner |
Lighting a Glass Dome: You could decide where you want the light, for sure, and then drill a hole into the base, cut a groove into the underside of the base and run the wire into the groove and out the back. Of course this will only work with hard wire, not tapewire. Roz Weitzman in Toronto |
Fiber Optic Lighting: Dolls House World Magazine, issue 98 November 2000, pages 15-15. Jane Laverick talks about using a fiber optic torch used for flower arranging to wire a 1:24 scale kit. The article is a multi-part, there's more next month, and not a lot of detail on the lighting so far. Jane mentions the issue of the fibers not bending round right angles but doesn't say how she gets round the problem at the corners of rooms or when going through fittings. I eagerly await my next issue.... Sandra in New Zealand |
| Previous 10 | Next 10 Page 902 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |