Tape Wiring: You MUST remove any brads that you installed incorrectly. It will cause a short and your electricity will NOT work. There is a very good booklet entitled DOLLHOUSE LIGHTING Electrification in Miniature by Barbara Warner (Boyton and Associates, Inc. Publisher) on how to electrify dollhouses and room boxes. I suggest that you purchase this booklet. She explains, in detail, the how and why of tape wire and hard wire. Also, why you have "shorts," which is basically when the electric flow is stopped. I knew nothing about electricity or electric wiring, used her instructions, and haven't had one problem. My first project, a three story dollhouse, has been tape wired since 1991 and all the lights still work. Most miniature shops carry this publication and I have even seen it in A.C. Moore, a popular craft store in our area, - Bensalem, Bucks County, Pennsylvania.

Caroline K. Bradley


Pin hinge doors: The secret to pin hinge doors is to set the pin exactly halfway between the front and back, and exactly the same distance from the hinge end of the door. So if you have a door that is 3/32" thick, your pin would be set 3/64" from each side and 3/64" from the hinge side (that's the narrow edge). Also, you may need to round off the square edge of the hinge side of the door to allow the door to open. A little experimentation will get you going. Predrill for the pin with your pin drill, nip off a straight pin and put it in the hole, and put the other end(s) through the hole in the top and bottom of the space the door sits in. It makes it much easier if you can arrange to set one of the pins in place, put the door in place, then put the other pin in through the bottom border of the door space and into the bottom of the door.

Jeanne


Porcupine quill chairs: It helps to copy a simple chair shape, such as a kitchen chair. Cut the quills to the length of back legs, front legs, seat rails, top rail etc. Use pins to anchor them to each other, and glue. Make a solid seat of card and foam and cover with velvet. You're aiming for an opulent look. Glue in place. Finally place small beads, held with pins, pushed into the top of the back leg (ie stile) quills. When completed, the chair will be simple in construction, yet curiously opulent and very pretty, reminiscent of Anglo-Indian furniture in the time of the Raj.

Helen


Electrical: Masonite is a brand name for Tempered Hardboard (kind of like a high density fiberboard). It holds up pretty well. It is near impossible to wire (can't get brads or eyelets into it worth a darn - it's too hard). But not if you use eyelets and the Connector Tool available at Earth and Tree from Tom Berkner http://dollhouse-miniatures.com  or contact Tom tom@dollhouse-miniatures.com We even experimented on arborite and it goes on just slick. What a timesaver, and makes the job so easy. No, I don't have anything to do with this company other than I am a very satisfied customer and just love the excellent service.

Jonesy


Overstuffed Furniture: The Small Scale Cabinetmaker series has a booklet on overstuffed furniture. It is absolutely awesome. There were several references to this series a while back for a person looking for cabinet patterns. I don't have the link right offhand, but I am sure that someone will provide the web address for you. Helen Ruthberg has several books that also have patterns in them for upholstered furniture.

Debby


Wiring: I always cover my wire tape with masking tape to protect it from the wallpaper paste. Haven't had any problems so far.

Colette in Dubai, U.A.E.


Overstuffed furniture: There is information about overstuffed dolls house chairs and sofas in Venus Dodge's 'Dolls' House Needlecrafts and Sue Heaser has written a book on Making Dolls' House Dolls from Fimo - that may be the title but I'm not sure of that one. Both are in print.

Chris


1/4-inch Nursery Furniture: Sherri of Domestic Dragons in Florida has a crib, chest and other nursery furniture. Her e-mail addy is: sherridragon@earthlink.net. I love her kits, which are easy and exceptionally nice.

Jeanette Zanio


Florist's Cooler Case: I do have before me the instructions for a florist cooler. Laura in OKC is right: it's a Joanne Swanson story in NN, May '87. It is constructed of matt board, wood strips, and styrene. If you plan a good-sized shop, you might be interested in the setup of some real-life places: instead of cabinets they have walk-ins, like closets but protruding rather than recessed. Glassed fronts and sides. One I've seen uses brick (or brick paneling) at the base, maybe 18" or so high, with a brick floor inside. Shelves at the back to hold arrangements, and room on the floor for buckets of long-stemmed cut flowers and filler greenery. Also if this was to be a garden center as well, access NN's April '91 issue: Garden Center by J. Swanson. Full of goodies.

Mary


Installing Brads: I discovered a great way to put in those little brads. I poked the hole in the tape where I wanted the brad to go with the tool they give you. Then I picked up the brad with a pair of tweezers and placed the head of the brad on a piece of masking tape, kinda molding the tape around my finger. I pressed the brad into the hole, then very carefully removed the tape. The brad will stay in place till you hammer it in.

Donna


Previous 10 | Next 10


Page 904 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)