Wooden Fan Uses: I used some of the pieces for making a fretwork headboard and sofa backing. It breaks so easily, but will work. I just finished a bakery display case (one-inch scale) and joined two pieces together to form a design that I glued onto the back for a fancy effect. Actually, I think of it as the pauper's Bespaq technique. I've taken plain furniture and attached little pieces here and there. I don't work with quarter-inch scale but I would think it would make a great screen, also architectural molding if cut just right. I've probably ruined more than I've actually used but have saved most of the pieces. I wish I could find another one with butterflies 'cause they are so purdy!

Theresa Thomas


Fans: We use the wooden fans to simulate fine fretwork or ironwork on minis. Decorate panels of cupboards, make an oil stove, chair backs, tiny cradle, and waste paper bin. Could use to decorate small windows. They have a lot of uses but you have to try them several ways sometimes because every type of fan is different in design.

Roberta Pijper


1/4 Scale: I have discovered that Dritz - the sewing notions people - no longer sew their hooks and eyes to a piece of heavy paper Now, they package them in a sheet of plastic 'cubby holes' with a paper backing. The little 'cubby hole' is just about right for making sinks and washbowls in quarter scale.

Dani


Unlit Chandelier: You can find extra large triple fish hooks in the sporting goods section at Wal-Mart, KMart, Target, etc. Use one for the armature. Use safety goggles and cut the barbs off, then choose whatever beads you want and glue on the ends. Use big round ones for a Victorian gas lamp look or use flatter, metallic beads, gluing grommets on top for a more wizardly look. When dry you can use tacky wax or more glue and insert real candles or painted toothpicks into the grommet "candleholders." Then join the chandelier to a plain shank button with a jump ring, and glue the button to the ceiling. For a more formal look, use crystal beads and drape strands of old necklace between the hook arms for a crystal chandelier. You can also wire teardrop-shaped beads as pendants under the "lights." I use these all the time when I rehab houses for charity. They are a classic of dollhouse DIY.

Loretta Sniarowski


WORKING CEILING FANS: Appliance timer motors are reasonably small, geared motors that advance the cycle switches on your washer and dryer. The ones in washing machines have a nice speed of between 4 and 6 revolutions per minute. Used to drive a four blade ceiling fan, this passes one paddle over any given point about 16 to 24 times per minute. It works out as a nice lazy speed to offer a ceiling fan in a store, tea room, or kitchen. There are three solvable problems. While "reasonably" small, they are not miniature. Also, they run on 110 volts so you will need a separate electrical circuit unless you have reflective lighting in your dollhouse.

As for the size, mount it on the floor above the ceiling where your fan will be. This will require preplanning for decoration if that space is to be a decorated room. I have hidden these motors with bottomless trunks, a bed, and a raised false floor. The shaft is usually a small pin. A shaft of KS brass tubing used to build your fan can be slipped on from below and secured with a drop of super glue for final assembly. Build the fan with findings, wood, and that piece of brass tubing. Sorry, I have never worked out a way to have lights stay in place below the fan blades.

The third problem is that these little gems are expensive when new. The solution to this is to take your tools with you the next time you go dumpster diving. Do test the little bugger when you get it home because this easily replaced motor is frequently the reason some washers end up at the dump.

Mel Koplin in Las Vegas


Battery lights: Cherry Tree has battery lights for dollhouses - a 10 or 20 light set! http://www.cherrytree-online.com

jo


Wiring: You can put the lamps in one of 2 ways:

1. Put outlets in the tapewire and plugs on the lamps. Use the small outlets and plugs. I use this method for lamps as it gives me flexibility to move the lamps around.

2. If you use eyelets, make a hole for the eyelet, wrap the lamp wire around the eyelet, and push the eyelet in the wall. Make sure the eyelet fits tightly. I use this method for chandeliers. I run the chandelier wire through the ceiling to the floor above and install the wires in tape that I have on the floor.

I've done lighting both ways and have not had a problem If your tape wire is under wallpaper, you need to have a tester to find the location of the wire. A tester has 2 prongs and a light bulb inside. When the tester lights up, that shows where the 2 edges of the tapewire are located.

Carol


Wall Sconces: It is difficult to paper after you get the lights installed. Here is what I do: If I want a sconce on a wall I will paper it and then link to light to the other side of the wall and then paper that wall. Most of the time you install the lights after you wallpaper. This is of course if you use tape. I measure where the tape is and then press in my fixtures. I use the ceiling fixtures that press into the tape also. If you use wire it is tricky but what I have done is punch a small hole through the paper and then hang the paper with the sconce at the same time. I am doing a roombox for a contest now. I ran my tape around the bottom section and I will hide my wires as I go. If I put a plug in the floor then I do it as part of the floor installation. For fireplaces and hearths I wire them to my tape through the hearth and then panel or paper over them. I attach wall hung lights to the other side of the wall before I wallpaper that wall. Earth and Tree has the punch to add rivets to the tape system and it really makes life easier.

Bill Leimberger


Soldering Tape Wire: I have always used a direct wire system and by that I mean that I always cut off the plugs at the end of fixtures. It seems they are always out of scale and I don't want them to show, so I cut them off. Then, using an X-acto knife, I carefully separate the wires so that I have two. This part requires extra caution because the wires should retain the insulation at the point where they separate. After I have separated the wires, I solder one to each piece of the tape. If you are using the newer, double tape, you will first have to scrape off the insulation on each tape at the point where you want to solder. Unfortunately, the solder will not go through the heavy insulation on the tape and you cannot get a good connection without removing the insulation first. I am one of those from 'the old school' in that I much prefer the single copper tape to the new double blue/ pink tape that is available everywhere to day.

Nancye in Miami


Soldering Tape Wire: You remove the plastic coatings from the top of the the bottom piece, and both sides of the top piece. Apply a little flux, heat the junction with a soldering iron, and touch the solder to the edge of the top piece - capillary action will draw the solder between the pieces.

Tom Berkner


Previous 10 | Next 10


Page 905 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)