Wall Sconces: Determine how far up the bare wall you want your sconces. Assuming you have the tape firmly in place, you cut the wires off the sconce to the length you need to reach the tape and attach them. As you know, I prefer solder, but you can attach them with brads or grommets. Lay the sconces on the floor until you are ready to wallpaper. Cut the paper to fit the wall, mark where you want to sconces to go, cut an X at that spot. Carefully thread the sconces through the hole made by the X, leaving only less than half an inch of wire showing behind the fixture. Fasten down your wallpaper, glue down your sconce, and there you are. If you plan to use the sconce adapters, put a brad in the tape where you want to attach it, leaving about 1/8" sticking out of the wallpaper, poking the brad through the paper. Now you know where the sconce adapter will go and you can attach it directly to the wire. Dottie in Tucson |
Different Lighting: I have seen a totally different system of lighting used by a friend who used to be in our mini club. It uses no wire, but it does use strips of aluminum or some other white metal, laid down under the flooring. It has to have a thin floor that a pin will go through easily. (These details are only from what I could glean from two short discussions with Dave Crandall during busy shows.) Each object to be electrified has a couple of small pins on the bottom that make contact with the metal. Now here's the fun part. The metal isn't electrified even enough to tickle your wet tongue. A couple of guesses as to how it works. I'm sure that you electrical technologists can help out here...? It may work on the same principle as the automotive timing lights that came out a few years ago that only had to be attached with a clamp to the outside of the spark plug wire. The clamp never really comes in contact with the actual wire or electricity. Maybe it has something to do with an electromagnetic field? Dave Pierce |
Tape Wiring: I put a layer of shirt-weight cardboard on all of the walls. Then I tape wire to the cardboard. Then I make another layer of the lighter weight shirt cardboard and wallpaper it. I use a lot of lightweight cardboard. I get it from a local print shop. Wolfie |
Voltage Adapters: Radio Shack sells adapters (the thing you plug into the wall to operate a battery-driven item like a radio). They have one that can put out 3 volts, 6 volts and 9 volts. Now you just have to know what bulb you are going to use and the voltage it operates by. Bob in Hollywood, FL |
Installing Light Fixtures on Slanted Ceilings: I use a 3/4" or 1" stripwood (about 1/8" thick) the length of the room, installed at the peak of the ceiling for the ceiling light. That way your fixture is on a flat surface and the wiring all runs above the stripwood to the side of the room or house. Attach the fixture before gluing the strip to the ceiling with the wires hidden. I use scrap wood or whatever I have on hand to wedge the strip up until the glue dries. Fannye in TX |
Fixture Parts (Bulbs, Attachment Parts, etc.)/Metal Tubing: All of Cir-Kits lighting stuff is on my website http://www.dollhouse-miniatures.com, along with some of the JAF findings. The only thing I've seen for bending small tubing is a set of springs that you slip the tubing into and they help prevent kinking. Probably the best way to prevent kinking is to buy some of the very low temp. casting metal that Micro Mark sells (it melts in boiling water). You melt the metal and fill your tube with it. Then bend your tube. Since it is now in effect a rod, rather than a hollow tube, it can't kink. When you have the shape you want, drop the piece into boiling water, and the metal filling will flow out, leaving you with a perfectly shaped tube. The metal is reusable for ever. Tom Berkner |
Candles in Pringle Cans: To make Pringle cans safe for candle usage in mini scenes, you insert a mason jar screw lid ring, upside down, in the top of the Pringle can. After you decorate the inside and outside of the can, you can place a votive candle holder in the top. The hobnail design ones work the best because the hobnail catches on the ring and is more stable. They can usually be found at grocery stores in their candle section. Another good source for them is yard sales. The ring actually spaces the candle source a slight gap from the Pringle can, making it heat safe. The lit candle casts a lovely glow on the scene below. Anita Myers in Arnold, MD |
Lighting for Gift Bag Scenes: I use the battery operated lights on all my gift bags. I punch holes in the ceiling and then pull the six strings through the holes. The battery back will sit on top of the ceiling. I then add tissue to the top which will hide the battery back. I have pictures of a couple of finished bags at my craft website http://members.aol.com/muscka/Minis1/index.htm Marsha, Newark, CA |
Wiring Tips: There are wiring tips on my web site http://www.dollhouse-miniatures.com Look under Tom's Tips. Tom Berkner |
Quarter Scale Lighting: Check out HO scale street lights for your 1/4" outside light. Go to your nearest railway shop and look for old style wall lamps. I used an old BRAWA wall lamp (Model 5356) as an outside light on a 1/4" scale house I recently made. Here's their web site - (go to English version, accessories, lighting and take a look at their antique and also the N scale wall lights - unfortunately it doesn't show the lamp I used but it will give you a feel for the kind of thing I used) http://www.brawa.de/ Sandra in New Zealand |
| Previous 10 | Next 10 Page 906 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |