Strip Lights: The name of the strip light that I have used is "Starstrip Mini Shelf Lite" and is distributed by Yorkville Industries Inc. Amityville New York 11701. They come in 10", 20", 30", and 40" lengths and in brass, chrome, white or black holders. The bulbs are rated at 6 watts and 120 Volts. The plug can be removed so the cord can be threaded through a small hole and the plug reattached. One drawback is there is an on/off switch that is rather close to the light and it is not removable. I solved that by prying it apart, threading the wire through and then installed a new switch so it is outside the box.

June Simpson


Wiring a Ceiling Light: You can groove the ceiling and then spackle over the groove with wire. I would then texture the ceiling or use ceiling paper. I have also used beams to carry the wires. Just make a U shaped beam or groove in the top side of a 1/2" piece of basswood and put the wires in that. I prefer a somewhat larger beam in 1" scale houses.

I like to use two 1/4" square strips covered with a 1/16" x 1" stripwood. That leaves you 1/2" in the center to carry the wires.

Fannye in TX


Candles: This is especially good if you want a thicker candle such as one in a centerpiece. I take a dowel of whatever size I want and paint it with acrylics. After a couple of coats, I then "scrape" the brush filled with paint at the top of the candle to simulate the effect a burned candle has. For a wick, you can drill a fine hole and put either thread or cut a piece of the plastic that comes with clothing tags and paint it black so it look burned. Those gizmos also make realistic straws for glasses of lemonade or other cool drinks.

Jeanette


Glass block windows: I read the response from Carol to Pat about the glass blocks. She mentioned grids for light fixtures and I instinctively looked up at the fluorescent fixtures in my office. Voila! The fixtures are those 2'x4' jobs common everywhere. The covering panels look just like those glass blocks turned on the diagonal! I know they sell those replacement panels at Lowe's and I bet they sell them at Home Depot and hundreds of other hardware stores. You might see if they would work for your purposes.

Sonia


Lighting with Batteries: You can use batteries to light lights in a miniature scene, but the batteries do not last very long. If you use AAA, AA, B, C or D batteries you need either 1-1/2 volt lamp bulbs or 3 volt lamp bulbs, depending upon how you wire up the batteries. Most mini light fixtures, at least in the US, are 12 volt and would really not light to speak of on batteries. You can light 12 volt bulbs dimly with a 9 v. battery, however. Again, light life is the big issue, and there is no way around that. Our transformers are rated at 12 volts, although many of them are "too hot" and run as high as 14 volts, which shortens the life of some brands of fixtures somewhat. Not a simple subject!

Barb Jones


Wiring Foam Core Boxes: When I wire in foam core, I make a long needle from some stiff wire with the end bent into an eye. I thread a piece of wire through the eye and run the needle all the way down through the middle of the foam, down a wall, and run the other wire in its own place, no need for insulating what is in the wall that way. You can do the same thing with the drill bit someone mentioned, just two holes instead of one.

Please remember all joints should be soldered and any joint that might be able to touch another bare joint should be insulated with shrink tubing or silicon caulk. Electrical tape is of such poor quality these days that I don't recommend it, and it is bulky besides.

Barb Jones


Polymer Clay Molds: You can use polymer clay to make molds - it works pretty well for something's - less well for others. Novelty buttons work well, so do small castings, charms and components - depending on their shape and complexity. I had hoped to make oval frames but found that they distorted too much when taking them out of the mold.

I start by taking a ball of clay and softening it. Flatten the ball slightly. Dust the surface of the ball and the item to be molded with talcum powder. Push the item - such as a button or a finding, into the softened clay. Remove the item (hopefully you used enough talc - if not roll the clay up and start again) Examine the mold carefully - look for cracks in the clay - if the mold is not perfect start again. When you are satisfied with the mold, bake it as recommended on the packaging.

When using the mold - dust liberally with talcum powder to prevent the fresh clay from sticking to the mold. Soften a ball of Fimo and push into the mold. Remove from mold- trim away any excess and then bake. You can use the mold over and over again.

Lesley


Home-Made Air Dry Clay: You can also use tiny amounts of poster paint to color it. Use just a touch from a toothpick dipped in the color. Or you can paint when it is dry. You could also try the gel color, not the liquid, it makes it too wet. The clay keeps for weeks in the fridge. I color when needed so you aren't stuck with too much of one color.

Roberta Pijper


Wiring Foam Core: I hard-wired my half scale house. The house is shown on p.58 of the current issue of Dolls House and Miniature Scene Magazine (website is www.emfpublishing.co.uk). The problem is how to get the wire through the walls. For this I used a long drill bit which I believe is called an "aircraft extension" for some reason. It is an 1/8"bit with a long shaft, probably about 6". I used a cordless drill which is not as powerful as a corded one, and drilled through the foam wherever I wanted a wire to go. If the wall or ceiling is held up to the light, the path of the drill can be seen. In my house all the wires exit the walls or ceilings under the staircase where they are hooked up to barrier strips, and the lead-in wire joins on the other side of the strip.

As for fire, it is not any more dangerous than plywood. Regular Foamcore, which is covered with a paper, might be dangerous to wire. Gatorfoam is covered with a plaster-like material. If two wires do not touch it is unlikely there would be a fire. To add more wire to a lamp or bulb, for instance, stagger the solder joints. By this I mean to cut one wire shorter than the other and that will mean the joints are not near each other. Then insulate the joint. This can be done using silicone sealer to surround the joint, or use shrink tubing from an electronic supplier. Use a transformer that is rated for the number of bulbs being used. Count a fluorette bulb as 3 bulbs. If the transformer is not rated as having a thermal protector then it is safer to install a fuse holder in one wire of the lead-in wire.

My house was shown in La Musee de la Civilisation in Quebec City for a year with the lights on all day six days a week and only two burned out in that time. At least, I presume they are burned out as I haven't had an opportunity to check them.

June


Mold Making Method: For many years I worked with natural liquid latex. It also is available as a synthetic called Neoprene. It is not that costly and can be obtained from some Home Depot stores or at times from carpet laying stores. Procedure; Make your original piece. Make it out of Fimo, plaster, what ever firm substance permits you to create your "thing." Attach some form of holding device to the base. Think of a lollipop or ice cream on a stick. Place the thoroughly mixed latex in a container that is deep enough so you can dip the master model into the latex and have the latex completely cover the model. Like dipping a Jelly Apple. The model is prepared by giving it a good dusting with talc or rubbing it down with powdered plaster of Paris.

When stirring the latex do not be too vigorous as this creates bubbles that adhere to your model and become a source of extra work. Holding the model by the lollipop stick, dip it into the latex. Turn it right side up and let it drip and dry in that position. Repeat this process of dipping and drying about 10 times. This creates a wall of thickness that can support many pourable mediums. When this method is used a model that has some undercuts can be reproduced. After your casting mold has been made trim off the drippings and excess from the base of the model and pull the rubber mold from the model. The mold will be inside out at this time. Inspect it for any defects such as shallow craters made by unbroken bubbles, fill these in with a drop or two of latex. On occasion there will be little "nipples" created by the latex finding small holes in the model and running into the holes. These can be sniped off very carefully. After this inspection your negative cast is ready for work (almost) To avoid air pockets when pouring material into this

negative mold make a pin hole in the lowest part of the mold when it is in the upside-down position. This will allow trapped air to escape when the positive mold is poured into the negative mold. Dust the inside of the latex negative mold that you have made. This is the "separating medium" that will allow you to pull the flexible latex mold off your poured positive replica.

Of course hold the hollow mold with the opening "up" or it becomes impossible to pour anything into it. This procedure is good for solid reproductions. If you have a model of a person with his/her hands on their hips. this method is of no value.

Bob


Previous 10 | Next 10


Page 907 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)