Toaster Oven: I have been using a toaster oven for Sculpey and Fimo since before there was Fimo (1975). I never use more than 250 degrees and never cook it too long. Sometimes if I'm in doubt I drop it in cold water and see if a nail makes an indentation. It doesn't matter if it's and old one or not. I bought one at a garage sale 2 years ago and it's fine. If it smokes the thermostat may be off and you may have too cook it even lower. Gail |
Clay and ovens: if you are making just a few things from Polymer clay you can use your regular home oven. If you are planning to make things time after time in bulk a toaster oven is better. You have to use a good quality and large size taster oven. If it is too small the elements above your precious clay piece will burn it. That is why someone wrote they can only make 'flat' pieces. Looking for making Miniatures in Polymer Clay. There are two books by this name. One is Sue Heaser's and one is mine. The one I wrote is available from Earth and Tree or Scott Publications 1800 458 8237. Mary Kaliski |
Evenly rolling clay: When making candy or other items that require an evenly rolled piece of clay, I place a tiny ball of polymer between two toothpicks and roll across those with my roller, thus ensuring even thickness throughout. Guess you could always find something thinner than toothpicks is you need to roll the clay thinner. Karin |
Mini lights: I don't know much about fiber optics, but Michael's has (had?) a battery pack that took 2 AA batteries and ran 10 itty-bitty lights (grain of wheat?), each on a separate wire. It even has a switch to turn the lights on and off. I think they were intended for wedding bouquets, but I used mine last year to make luminaires. Not an original idea; I saw it in the Miniature Gazette. I cut squares of 1/8 " balsa about 3/4 inch - which was a bit large - and poked a hole in the center of each one. I cut strips of lunch bag 1-1/4 x 4 to go around the block. (This was a bit long and had to be trimmed.) I folded the paper under 1/4 inch on the long edge before I began glueing, then wrapped it around the block, so it sat up to resemble a small paper bag. I then stuck the bulbs up into the bags from the bottom and there I was! When I set it up next year, I will make a little groove on the bottom of the wood to accept the wire and put a bit of masking tape to hold it in place. The battery back went under the porch steps, and the wires got hidden in the bushes and 'snow'. Dani |
To solder wire to tape: If it is the bare tape, then just put a little solder paste on the end of one wire and touch it to the tape and apply solder with the soldering iron (less than 30W), and do the same with the other half of the wire to the other side of the tape. It is not really necessary to use soldering paste but it does make the solder flow more easily. Use electronic solder and ordinary soldering paste (not plumber's solder or paste). If the tape has a plastic covering then scrape away the plastic wherever you wish to solder. June |
Regarding other ways to wire, we have used automotive dash board lights (they are 12 volt) behind various cornices or valances. They draw more current, so use a big transformer or a few lights. They give lovely indirect lighting. The sockets for them can probably be found in an electronics store of some kind. Take a bulb with you. Some people use the 7 watt night lights (they are 110 volt) but I find them way too bright and way too hot for dollhouse use. All waxed pictures will slowly slip to the floor! Barbara Jones |
Star Light: When I want a starry sky for my fairy scenes I use t-shirt lights! Cut a piece of cardboard to size of box, paint it the shade of blue you want and while the paint is still wet cover it with flocking. At your local fabric store in the t-shirt section they sell a strip of twinkling lights (clear or colored) powered by a small battery pack. Each of the 12 lights is on a separate wire. Poke a tiny hole in the cardboard and poke the tip of the bulb thru -12 times. The wires and battery pack are hidden behind the cardboard sky. This gives beautiful results as anyone who took my mother nature class can tell you. Sue Thwaite |
Night Sky: Has anyone suggested using 'blackout' material, used to line curtains to stop any light coming through curtains? In the UK this can be bought from most shops selling curtain fabric, and it lets no light through at all. Usually sold in white and cream, it could be painted dark blue or black, then pierced to make pinholes for the light to come through. Helen Cottrell |
Ott Lights: Several of the large office supply chains carry the Ott Lights, everything from floor models to table models but be sure that the one that you get says TRUE COLOR on it ... the bulb is a "U" shape, not a straight shape. When they were first introduced the company did not differentiate between the Task Lights and the True Color Lights with the result that many people bought the wrong one thinking they were getting one that would help them see colors at night. There are still some of the original unmarked lights on store shelves so look carefully before you purchase. I have a True Color Light and love it for night work and for that extra bit of light to chase away those annoying shadows that can make doing a small project very difficult. Sammy Smith |
Ott Light: If you want just the task light, Office Depot carries them for I think, $39.00 If you want the true color light, checkout Hofcraft at http://www.hofcraft.com they are the cheapest I could find at $59.00 For an explanation of the difference between the lights go to http://www.stitchers-paradise.com I recently saw the one with the magnifying glass at the A.C.Moore store for $99, so other craft stores may carry them also. Rose Stout |
| Previous 10 | Next 10 Page 909 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |