Wiring on Foamcore: The Cir-Kit booklet warns against using tape on Foamcore unless you use wood blocks under the junctions and outlets. I would guess you could hollow out the foam and insert a piece of wood in the spots where you plan to put the brads. IMO it would be easier to just use the round wire than to go through all that -- you can solder the points on the outlets and fluorette holders right to the wire. Rose |
Outdoor lighting: The showcase bulb for the fluorette is a super bright 200 ma compared to the regular fluorette of 180 ma. If you want a subdued light, use a 16 volt bulb. It works off the same transformer as the 12 volt but draws less current so is not as bright, plus it lasts longer. If you have enough lights you may want to try using the Houseworks Lighting Control Panel which has the option of putting in diodes for dimming one or more of the lights. Rose |
CIR-KIT Bulbs - Cir-Kit makes a 'Spotlight' bulb which is approximately 3 times the amps of their regular bulbs. I've used them in my Brooke Tucker box outside the windows to simulate sunlight and was really pleased with the results. They come with a swivel, metal attachment which can be screwed, nailed or even super-glued to your structure and point the light where you want it. Laura |
Wiring Log Cabins: My only suggestion for wiring is to hard wire it and then "hide" the wire under a very small (and stained to match) channel (that is sort of a U shaped piece of wood). Renee |
Log Cabin Wiring: I am in the process of building a RGT Adirondack Log Cabin and "logged" the inside walls with the same logs as the exterior. However, before the logging was done inside, I tape wired the walls and made all electrical decisions where plugs would be located. My dad helped me "recess" the plugs and made cutouts in the logs where they would be located with a band saw. I also was able to place sconces on the walls by threading the tape wire "in and out" between the logs on the walls where the sconces would be located. The electrical work was really pretty easy compared to measuring and cutting all those logs, but now that the work is done it looks really great. Kathy |
For soldering tape wire, you do have to scrape the tape off where your solder joint is going to be so you have a metal to metal connection. Anywhere you would normally use a brad or whatever to make the connection is where you scrape and solder. Solder flows better if you heat the copper junction before applying the solder. Only problem here is the heat may lift the sticky tape up from the surface. It is a bit tricky and you probably want to practice on a scrap board first. I think CirKit or Electalite or someone years ago made a luan mahogany practice board with diagrams and how to's printed right on it. I don't know if that is still available or not. Soldering isn't all that hard, but be sure you use the right kind of solder. I buy mine from Radio Shack but you can get it almost anywhere. You want the kind that is especially made for electronics and already has the flux incorporated into it. Don't use plumbing solder or stained glass solder. Tinning your iron means getting it hot, then wipe it off both sides on a damp sponge and touch it to some new clean solder. You can wipe it on the sponge frequently to keep it shiny silver looking as you work. That makes it flow better, I guess it removes oxidation or something from the solder. Don't try to reuse old solder.. the flux is gone and it won't flow properly. I even solder tape connections, but that requires being a little more skillful. Bonnie |
Lamps: Radio Shack has tiny bulbs, all kinds of wires, transformers, solder and connectors. Most mini and train stores carry at least some electrical equipment. Make sure you know what the voltage is; a 3v lamp burns very brightly for but a moment when it's hooked up to a 12v transformer. Bead stores can provide lots of good lamp bases, and lovely glass shades if you're lucky. International House minis has a great selection of lamps, plus some electrical, and Royal Minis has some nice glass hurricane lamp chimneys. They're both wholesalers, but Suzi's Dollhouse can order them for you. ( http://www.suziesdollhouse.com , I think, and she's got links on her ordering page to IH and RM). Stuff from Suzie's catalog ships quickly, that from the other catalogs may take a few weeks. Lee |
Lamp Source: Brooke Tucker has several of her lovely lamps for sale on her website - and now has a secure order form to order with your credit card! My favorites are the Book Lamp, White Rose Lamp, and Spring Bouquet Lamp. http://www.brooketucker.com Anne Gerdes |
Hot Transformer, Dim Bulbs: It's been my experience that when this happens, the transformer does not have enough wattage for the amount of bulbs it is powering. ....at least , this is true for Cir-Kit brand transformers. Don't know about the other brands, because I've never used anything but Cir-Kit (with good results, I'd like to add). There is a little 'breaker' built into the transformer; when it is overloaded, it 'breaks' just like real-life circuit breakers and cuts off....after a time, it resets itself and restores the connection to your lights. I'm thinking this is what's causing your lights to be dim, too....again, if the transformer can't handle the number of bulbs, the bulbs may light, but be dimmer than normal. Here are some basic guidelines from Cir-Kit for matching up your number of bulbs to the wattage of each transformer....keep in mind that these are maximums (for bulb count); you may still have dimmer bulbs unless you upgrade to a stronger transformer: 3 Watt Transformer - 5 bulbs max One more thought: Have you tried plugging the transformer into a different outlet in your house? It may be the outlet itself. Laura |
Flickering Lights: The most likely causes of your flickering lights are 1) copper oxide has developed at the connection of some pins and the copper tape and the connection is less than good, or 2) a pin has become loose where it goes through the copper and the connection is weak. It does not sound like a short, but more like a connection that is opening and closing. I don't know what to suggest but to move all the pins over a little. Copper oxide is not a problem if every connection in the dollhouse is a soldered one. Barb Jones |
| Previous 10 | Next 10 Page 911 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |