Battery operated light strings. Try www.christmasdepot.com. Gene Ann |
Tape wiring: The wet stuff will not hurt the tape in tape wiring. Any time moisture is a problem is only when you stick the connectors to the tape. When you do that it will all be dry, so I see no problem. Barb Jones |
Applying Mortar Over Tape Wiring: When I get to the point of applying mortar, is the moisture going to ruin the tape runs? Probably not. The tape is covered with a thick layer of plastic. If you are shaky about it, put another layer (in the form of packaging tape) over that and it will put your mind at ease even if it isn't strictly necessary. I usually do that when taping over a floor that will be covered with carpet or wooden flooring to help protect the tape wire. Dottie |
Dim Lights: Check the output voltage and amperage of the transformer (ie 9.0v-DC/265mA) and try to match the lights to this. Remember, if you are using a series (all lights in a string) the more lights on a circuit, the dimmer they will be and if one blows, they may all blow and will certainly not work until the blown bulb is replaced. If using a parallel circuit (each light on a separate path) brightness is determined by the rating of the individual bulbs and if one goes, others are not affected. Dani |
Dim Lights: First, Don't tap the lights with anything. When you do that, you are basically shorting out the filament in the light. Depending on the type, it may be a coil like a spring, or it may be a couple of big loops which are barely supported. When the filament is hot (emitting light), it is very fragile and by tapping, you cause adjacent coils to touch each other, thereby making the filament shorter than designed. The filament length is designed to drop (use) the 12 volts without overheating. When the 12 volts must be used by less wire, the wire becomes hotter (brighter) and it shortens it life drastically. Count the number of light bulbs you have in your house (bulbs, not the number of fixtures or lamps). Double that number, and then divide that result by three. The answer is the approximate number of watts (output, not input) needed from your transformer. If the need is greater than the size of your transformer, the bulbs will be less bright and the transformer will overheat, causing the thermal overload to open up, turning of the power. When it cools down, it will reset and turn back on. You solve this by getting a larger transformer. There could be a couple of other things, but check this first. Tom Berkner |
Two-Light Transformer: Cir-Kit makes a 5 bulb transformer, which is what you would need as that is the smallest that I know of. For two lights, you could also use a battery pack, but you would have to hardwire it onto the tape wire on the outside and the lights will not be as bright! Cir-Kit does have a web page and it is http://www.cir-kitconcepts.com. Isabel Allen |
Two-Light Transformer: Depending on the bulb(s) voltage I think one of those little transformer/converters that plug into the wall and then to the radio or the answer machine will take 110-120Vac and give you a lower voltage DC I have used them for 6.0Vdc; 9Vdc and 12 Vdc. With a single bulb as you say there is no need to worry about the Ma. (milliamps) that the transformer can handle. If you have one and the output Vdc is to high for your bulb, you can use a "dropping" resister. Bob |
Voltage Droppers: Voltage droppers tend to generate heat and some times quite allot, especially if you don't have the right rating , and for a light bulb there is no need of a DC. output, I think that it would be easier and safer to get the bulb of the same Voltage output, say if the transformer has a 6V output get a 6V bulb, etc., moreover the problems with transformers is the over loading, using to many bulbs not less, to cut it short, a transformer that takes 30, 12V bulbs can still be used for 1 or 2 12V bulbs and if they are to bright use a higher voltage bulb, say 13V or 14V and they light dimmer, or only one box room with 2 bulbs, apart from that a large transformer one can connect more then one box room to the same transformer, then the bulbs have to be the ratting recommended on the transformer, say 12V and not exceeding 30 bulbs. Joseph |
One-Light Transformer: I use a railway transformer for room boxes even with only one light. The beauty of the little one I have is it is plastic and therefore light and has the option of turning the power down and thereby dimming the light if it is too bright. Roberta |
Lighting Problem: Have you tested the transformer to be sure it isn't defective? Touch the ends of the bulb wires to the terminals to see if it lights up. Do the same with the test probe-you may have to attach wires to the prong ends in order to reach the two transformer terminals -- the small bulb in the probe may be burnt out. Until you know that you have current at the beginning of the tape run, I wouldn't advise going any further. Rose |
| Previous 10 | Next 10 Page 913 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |