Lighting Problems: Now to get to your electrical using the probe, is it possible when you hammered your junction in you might have not put the two prongs into the tape, or when you put the screw to hold the junction on you might have caught part of the tape it can happen. I do alot of electrical but this sometime can happen. Check it out because your probe should work that tells you all tape wire is okay along with the junction.

Patti


Brads & Tools: A brad is the same as a nail only much smaller and a brad awl is a tool to make a very small hole for the brad to go into. When I'm doing electrical I take a very small piece of bond paper about the a l" x 1/2" and I put a tiny hole in the center or near the end then I make a slit from the hole out. I place my brad into the little hole in the paper then I put it in the hole where my electrical is going to be then after tapping it in with the hammer very lightly I then pull the paper where I made the slit and then bang my brad the rest of the way down.

Patti


Lamp Parts: You can get lamp parts from a company called Tec Innovations. She also sells to retail stores so you can check to see if your local store carries the parts. Tecs e-mail address and web site is: http://misc.home.mindspring.com/ E-Mail teclamps@mindspring.com

Deb Laue


Lighting Web Site: He is in England but does do shows in America. His lights are fabulous - all brass and hand blown glass. Ray Storey Lighting http://www.storey-lighting.freeserve.co.uk/

Barbara B


Wiring through Hinges: I've done lots of wiring with all kinds of copper tape and can't think of any way to wire through a single (piano) hinge. Usually it takes two hinges, running each tape through one hinge. But you might stop the tape on one side of the hinge, start it again on the other, and connect the two with a short piece of wire or a plug/outlet assembly. Email me if you want more information.

Sue


Lighting; Wiring and lighting a dollshouse is not that hard to do. The voltage used is very safe. First, look at light fixtures. Decide what fixtures you want in your house and count the BULBS. The bulb count determines the size transformer you will need. You don't have to get all the fixtures at once time, though it's easier in the long run if you can get at least all the ceiling fixtures at once.

I recommend Cir-Kit wiring kits. Knowing your bulb count, look at the wiring kits (or ask your retailer for help) to determine which size transformer will meet your needs. These kits contain about everything you need to install wiring in your house except for the light fixtures themselves. They even have instructions! A very helpful booklet by Barbara Warner on basic wiring is also highly recommend. She makes it easy.

Once you have your wiring kit (and hopefully the book) you study your house to determine how to run the tape wire. Ceiling lights do best when the wires are poked through the ceiling and wired on the floor above. The instructions books will tell you how to make any joins needed and how to attach the fixtures.

Beth


When I teach the electrical class, I always stress making a plan and keep it somewhere you can find it later ( like in the base of the dh). Another thing is to test each room after you make any changes like adding wire. Then also I say when you have a problem, backwards one room at a time and isolate your problem. Sometimes it's the source, did you plug the transformer in? I've forgotten that when I'm in a hurry.

One other thing is that when I can I wire in the lights on the floor above the ceiling where the light is. You are going to cover it with wood or carpet and won't see it. Just make sure you don't glue the wiring in so you can never get to it again.

Deanna


Tape wire and floors: When I tape wire, I run the tape on the wall about 1/2" from the floor. That way it will be just above the baseboard. (I change that if I'm using baseboard that is a different height.) And to get from floor to floor above, I run the tape up the wall through the stairwell. The only problem you have is if there is no stairwell wall. That happens most often from a second floor to an attic floor. Then I look for a room, such as a bath, that might be getting a tile floor. I run the tape from the ceiling below to the floor above and head to the nearest wall. If that isn't possible, consider drilling a tiny hole and attach runs of tape on the floors with round wire. Just be careful of the size of wire in relation to the number of lights and tape that are above the wire.

Sue


Room boxes - You might be able to get the light at Radio Shack or a hardware store, I got mine from a miniature dealer. It is called "Auralite" (dramatic, under shelf accent lighting). It turns wall units, curios, stereo cabinets and bookcases into decorator showcases. Mine is 10": brass, energy efficient with 7.5 watts. You can glue or screw it into your roombox.

Mary


Stained Glass Windows: Dover prints lots and lots of mini pictures in stained glass format.

There are some that are in little books about 4"X5". All one has to do is color them in and they are ready to use. Perhaps there might be one there that could be made into 2 or even 3 windows.

Linda


Previous 10 | Next 10


Page 914 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)