Window Grills: The other day I bought lots of six-packs of impatiens, so I asked if I could have large plastic trays to carry them. I was given three plastic trays and when I arrived home I noticed that each of the trays had many wonderful open designs that could be used as window grills. All that was needed was a strong scissor for cutting and some paint. They fit on the windows beautifully.

FranCee


Frosted Glass: Stipple Weldbond on acetate or any clear plastic sheet, thickly, with a stencil or hard bristle brush. Let dry and you have frosted glass. For a crystalline look, paint thick short strokes varying direction of strokes.

Mary Kay Gentile in Ft. Myers, FL


Glass: I have some very thin glass for sale. It is .025" thick. That is just over 1/2 the thickness of the plastic that is used in some dollhouse windows. EARTH & TREE Miniatures and Dollhouses http://www.dollhouse-miniatures.com

Tom Berkner


Screens: use tulle - the fine bridal netting for the screens in doors. It comes in many colors and can be spray painted - carefully so as not to fill the holes. I recently used it as mosquito netting in a tent I made for my son's GI Joe. Looks great.

Susan in St. Croix


Glass Thickness: For those of you who really care (both of you) the following is a list of names and sizes used by the glass industry in the US to describe float* glass. ( ) are my comments.

6 oz .024-.032 (less than 1/32" - about the thickness of veneer)

Micro .036-.044 (typical of the plastic used in dollhouse windows)

Lantern .045-.051

Photo .056-.065 (this is what your local framing shop uses - incidentally they will usually give away scrap about 1/16")

16 oz .078-.085

Single .086-.096 (normal glass from hardware store)

Double .118-.133 (used when you need extra strength)

32 oz. .146-.160

3/16" .186-.200 (used for making bevels for stained glass work)

From here on up, they go by fraction measurements. Boroslicate glass goes entirely by fractional dimensions. *float glass is made by floating molten glass on molten tin; thereby giving a glass that is comparable in quality to plate glass, but at a fraction of the cost.

Tom Berkner


Mini Blinds: I made my blinds for my dollhouse by spraying a thin coat of white enamel paint on a piece of acetate. After the paint dries cut the piece to fit inside the window vertically leaving 2mm's on each side. Then cut 6mm slats and round off the corners carefully. Cut 2 pieces of wood a bit smaller then the slats and paint same color. Next depending on the size of your blind, drill a hole in the wooden pieces. Example: If your blind measures 3 inches, drill a hole a little less then 1/2 inches on each side. (Use you judgment). Line up one slat with one wooden piece having the same amount on each side and mark the slat where the holes are. Mark all the slats that you are going to use making sure that each one is the same size and hole marks are identical. ****Using a very fine sharp needle and thread, tie a knot at end. You will be tying a number of knots so please make sure you have enough thread. Thread through one wooden piece. Make another knot but DO NOT PULL TIGHT. First put your needle in so you can move the knot to where you want to set the first slat. This should be a little above the wooden piece. Once you are satisfied with where it is, pull the knot. Pierce a hole in the white painted slat and tie another knot a little above the slat. Repeat this until you have the length that you want for the window ending off with the 2nd wooden slat. You can make a loop or use very small metal rings to attach to window. **** Repeat other side.

Donna, Medford, New York


Mini Blinds: I have made non-working versions two different ways.

For bamboo type, If you can find "matchstick" type place mats, measure them to your window size. Cut with about 1 1/2" margin on the lengthwise edges and pull out the slats to the window size. This will give you some thread ends to knot and glue so the blind won't unravel. Then glue one end to a coffee stirrer and glue or tacky wax it to the top window frame. Leave down if you want the blind to cover the window, or roll up partway, slip some narrow ribbon between the slats, and tie in place to have half-open blinds. Use the wooden coffee stirrers. Cut to window width and pierce holes in each end. String with seed bead spacers between blinds. Knot and glue string when blind is window length. Fasten top slat to window frame as above. These will look like open wooden venetian blinds. Or make similar vinyl mini blinds by cutting strips cut from plastic packaging sprayed with acrylic to match your decor.


Gutter Guard Windows - The product I use is the plastic one although there is a metal one. It comes in rolls so when you cut the pieces for your window, play with it until you get it to lay as flat as you can. Cut the Gutter Guard to the desired size of window.

  • Paint both sides with a lead color gray metal paint. (acrylic is fine) and let dry. Lay the piece of Gutter Guard on a plastic bag.(Another use for those Ziplock bags!) Do not use plastic wrap as the window will stick to it and it is too hard to get off. With clear Gallery Glass, fill in all the little holes. Be generous and make sure all the gaps are filled. It will be milky but don't worry as it dries clear. Let it dry thoroughly. This will vary according to climatic conditions. Peel off the bag. Build your window and insert into your dollhouse. Voila leaded glass!

    You could use colored Gallery Glass for some of the panes if you wanted to get a fancy.

    Patricia in Whitby, Canada


  • Wire Mesh for Screening - Hobby Lobby have it. it is in the craft area, and in our store it is on the aisle with the cork. it is called Wire Mesh and is so tiny. the only problem is that ir only comes in copper and gold.

    Rebecca


    Raindrops falling down the window: Just drip clear nailpolish on the outside of the window in an arrangement that simulates the amount of rain you'd like.

    Alice Zinn


    Previous 10 | Next 10


    Page 916 of 1032.

    Total links in database: 10312.



    Search for:


    Browse the database (all entries)