Bakers Clay Plates & Bowls: For making plates and bowls and saucers etc., I have heard of folks filling in the thread holes in buttons and using them (the buttons) as plates. What I have had fun with is the use of Bakers Clay to make plates, bowls etc. Making the clay is fun in itself as it makes one feel like a kid with all the mess and goop. Bakers Clay, when refrigerated, can stay for weeks and you just pinch off what is needed. The upside of Bakers Clay is that it is almost unbreakable if dropped, as I have done numerous times. It takes acrylic paint readily and a glaze of clear nail polish makes for a faux china finish. The clay can be molded thin enough to be translucent. For plates, I would use buttons as a mold and when the clay is dry just lift it off the button. To make bowls, I use the rounded end of a carriage bolt as the form and mold the bakers clay over that. I do not wait for it to dry on the carriage bolt head I just remove it and set it aside to dry. By putting some powder on the carriage bolt head I can remove the clay very readily. I have found the dried Bakers Clay to be very light weight (surprisingly so) and slightly flexible (non-rigid.) This may be the reason for its non breakage. Bakers clay is VERY cost effective and can be had at midnight since you make it with readily available household items. No need to go to a hobby shop, which is usually closed at that time (VBG). The kitchen pantry is as far as you have to go. The Bakers Clay has a very long working time so there is no rush. No baking or kiln is needed. I have not had any bugs attracted to my Bakers Clay items and in SE Florida that can be the acid test. It can be, after setting,(I shy away from the expression "hardening") cut or sanded. Can be cut with a knife or good sharp scissors. No need to drill any holes as it can be punctured with any pointed object.

Bob in Hollywood, FL


Cornices: A small tip for trimming your cornices. I found it was easier to make plain cornices and trim them with Bunka or embroidery floss twisted. I used the pattern for a garden bench back turned upside down as the outline design on the ones in Summer Breeze B&B Living Room - used the same pattern in one of the other bed rooms - Summer Breeze Rochelle for the cut-out on the bottom. Hope this will help someone with a curtain/drape project.

Mabes


Watch for Holiday cards with the picture done on plastic (Acetate) overlay. You can use a Sharpie to draw "lead lines" for stained glass windows. These will not be high quality but can look nice in the background with light coming through. Another card tip, put up a notice at the senior center, library, or church hall, asking for cards to be saved for you and promising to make a few items for the next bazaar. I got over 600 that way one time!

Marcie Cumberland


Mullions: How about using Galaxy Glass Leading in an extremely fine line to simulate diamond-shaped leaded windows? Has anyone tried this? You can make this extra fine line by twirling a bit of clear tape around the spout of the bottle. This works for glue, too, doesn't it?

Linda


The very simplest curtains of all: Look in the trims department of your fabric store for trim that is intended to be used on lingerie, little girls' dresses, wedding dresses, etc. -- usually lace or "see through" type material. It's already gathered; just cut it to fit and glue it to the window frame. If you want curtain rods -- again very simple -- use the smallest diameter dowel you can find, paint or stain it, and use tiny screw eyes to hold it.

Linda in Colorado


Curtain Rods: How about trying bamboo skewers that are used for shish kabobs, or very a small brass rod which any train shop should have, or a twig from the yard for that rustic touch.

Susan Sawatzky


I use very small dowels for curtain rods. If you had really thick (comparatively speaking) wire perhaps you could use that, but without care, it still might bend if bumped, etc. Or a small brass rod (which I didn't have on hand). You could also use a 1/4 - 3/8" strip of wood to insert into a rod pocket of the curtain and have the wide (4" real) curtain rod. You would have to glue tiny pieces of wood as sides to go from the rod to the wall so reserve some of the gathered curtain to cover these pieces of wood. The top of the curtain (gathered on the rod) could be left exposed and simply pull the curtains back from the middle parting and use tiny tie backs. I made some like that in my workroom... no valance even.

Rita Pierce


Curtains / Drapes: They are so easy to make if you have a mini pleater... Just hem and pleat the fabric and you have wonderful pleated drapes. Curtain rods can be just about anything.. I've cut down wire coat hangers and glued beads at the ends for curtain rods... I'm sure you'll get lots of better ideas than that one.. but it does work. You can hang the rods on "hooks" that you've made from wires.

Viola Williams


I once saw an ad for Kirsch curtain rods that had a cluster of grapes and grape leaves on the ends of the rods for finials, this was in a bronze shade and was beautiful. I thought then, that the finials could be made out of fimo and using the fimo bronzing powder I bet they would look great.

Linda Reinhardt


Curtain Rods: Save the brass type pen refills that have the springs on them. They're usually found in those cheap "clicker" type pens. Make sure the ink is used up or you will get ink all over your curtains and walls. But you can then cut the pen refill the exact size to fit the interior of the window frame. The curtain rod is then "spring loaded" and you don't need any eyelets or hooks to hang it.

Paula Foerder


Previous 10 | Next 10


Page 921 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)