Chrome-colored Paint on Clay: Polymer clay doesn't react well with most finishes that are petroleum based. The finish will remain tacky due to a chemical reaction between the plasticizers in the clay and the solvent in the varnish or paint. Water-based varnishes cause no interaction with the clay. There are two spray brands that will work on polymer clay, too. They are Carnival Arts Ultraglaze and Krylon's Matte Spray Coating. Both need to be sprayed on in a very light single coat. These are clear coatings though, not chrome. Even some nail polishes stay sticky on polymer clay, so always test before you coat a finished piece of clay work.

I think that I would try a test piece of clay, with a clear coat of either water-based varnish or even thinned down tacky glue. Then try spraying with your chrome paint and see if the physical barrier of the clear coat will prevent the undesirable chemical reaction.

Tere


Painting Fimo and painting non-compatible materials. I have had some success using a barrier by Floquil. Floquil is a model railroad paint and Floquil barrier is for painting on plastic before using Floquil paints which dissolve or crinkle plastic. I have used the barrier on Sculpy with success. The barrier seems to stand up to different paints including lacquer. I would try it on something not precious or a keeper first.

Bill


Baking Electrical Wires in Fimo: I don't think the insulation on the wiring would stand up to the heat of baking Fimo. Suggestion: put brass tubing inside the Fimo and then bake it. Then you can run the wire in the tubing. If you need the tubing softer so it can be bent easier, then anneal it. That is to heat it until it is slightly turning red or a very faint glow. Don't heat it any more or it will melt. You can lay it on an electric burner and watch it very carefully. As soon as it starts to show a little color take it off (with pliers or tweezers) and put it into water. If you drop the hot tubing on the vinyl floor the floor is a goner.

Bill Hudson


Baking Electrical Wires in Fimo: I do not imagine that the temperature that Fimo is baked at will affect the wire. I would suggest that if the wire is insulated you place just a piece of the wire as it would be when it is imbedded in the Fimo and bake that alone in the oven. If it survives that test then you can bake it in the Fimo.

Bob


Baking Wires in Fimo: Why not bake your Fimo and then run the wire through it. I have made several lighted fixtures in this way. You can leave a place for the wire to exit and then thread it through.

Mary Kaliski


Roberta's Homemade Clay: Roberta's recipe for the self-drying clay is fantastic. We have been experimenting with it, and to color it (to save painting) we use food coloring powder. Take your mix and bit by bit put VERY little color into it, mixing very well. Be careful because when it is dry it darkens quite a bit! Just experiment with it. You can keep it in the fridge for quite a while, just wrap it in cling wrap and put it in a container (the less air the better). Don't use liquid food color because it makes it soggy. If you find it is too soft, add more flour.

Mirta


Baking Lighting Wires in Fimo: Don't put wiring in the oven. The insulation will melt off the wires and they might touch causing a short circuit. Instead, form your candlestick around something like a hollow piece of tubing, one with a hole large enough for the wire to go through, and bake it, then wire it.

June Simpson


Polymer Clay Sites: Here are some neat sites on Polymer Clay (Fimo, Sculpey and others):

http://www.heaser.demon.co.uk/sue/suetemp.htm

http://www.delphi.com/polymerclay/pcc/opening.html

http://www.sculpey.com/

http://www.yeoldouthouse.com/clayhints.html

http://www.prairiecraft.com/

Peggy


Air Dry Clay Recipe: 1 Cup Ponal (or other brand), Wood Glue (WHITE), 1 Cup Cornstarch, 60ml (12 Teaspoons) Baby Oil

Mix glue, oil and half the cornstarch. Heat in microwave 30 seconds until hot (do not boil). Mix in remainder of cornstarch and heat a further 20-30 seconds. Mix well. Kneed until smooth and store in a plastic bag in the fridge, Colour with powdered food coloring. Roll out thin to make flowers or to mold. Air dry. Do not bake. If it is too sticky add a little more cornstarch.

Roberta


Polymer Mold Coating: I have heard that if you dust lightly with corn starch, your mold will release with ease.

Michelle Geoffrion-Mahler


Previous 10 | Next 10


Page 928 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)